Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Members List
Reload this Page talos's Profile
Portal Register FAQ Members List Social Groups For Sale Gallery Calendar Search Today's Posts Mark Forums Read


talos
CC Member

Last Activity: 12-28-2024 11:33 PM

About Me

  • About talos
    Zip Code
    34787
    City
    Winter Garden
    State
    Fl
    Country
    usa
    Cobra Make, Engine
    Everett Morrison/Side Oiler
    Engine type and displacement
    427
    Tranny type
    Top Loader

Statistics

Total Posts
General Information
  • Last Activity: 12-28-2024 11:33 PM
  • Join Date: 11-01-2014

Likes Given

18 Likes
  1. talos
    talos liked post by eschaider On thread : Replacement Radiator
    It depends on your “originality genes.” If there are a lot of them and you have money to burn, go for it. Remember, no matter what you do, these cars are still replicas, not the original...
    Liked On: 12-27-2024, 12:06 PM
    Posted On: 12-27-2024, 09:21 AM
  2. talos
    talos liked post by eschaider On thread : Replacement Radiator
    This is the firm and the product you want, Delta PAG (https://deltapag.com/)
    Liked On: 12-26-2024, 09:12 PM
    Posted On: 12-26-2024, 08:11 PM
  3. talos
    talos liked post by Riverside racer On thread : Electric Fuel Pump 4 Webers
    I decided to look at what the high end weber fitted Italian cars used. And after chatting to mechanics the fuel regulator was Malpassi and a vane not pulsating pump. I use a Carter vane style pump...
    Liked On: 12-18-2024, 11:10 PM
    Posted On: 12-18-2024, 04:50 PM
  4. talos
    talos liked post by Eljaro On thread : Electric Fuel Pump 4 Webers
    I have been using a Carter Rotary Vane in line Fuel pump with my Weber setup. I also have used an Aeromotive ultra low pressure fuel pressure regulator #13222 which is very precise and stable, and...
    Liked On: 12-09-2024, 10:20 AM
    Posted On: 12-09-2024, 06:07 AM
  5. talos
    talos liked post by priobe On thread : Electric Fuel Pump 4 Webers
    There is a lot of wealth and knowledge here about these carbs. I prefer the wet gauge as I feel it is the most accurate in comparison to the tool you mentioned. Just my opinion. Keep in mind,...
    Liked On: 12-08-2024, 03:26 PM
    Posted On: 12-08-2024, 05:54 AM
  6. talos
    talos liked post by 1795 On thread : Electric Fuel Pump 4 Webers
    Unless you are racing, you really do not want to be much over 3.5 psi. In race you can get away with a little over 4 psi because you are running at WOT most of the time. As Paul said, get a good...
    Liked On: 12-02-2024, 08:47 PM
    Posted On: 12-02-2024, 07:47 PM
  7. talos
    talos liked post by PaulProe On thread : Electric Fuel Pump 4 Webers
    From experience, don't cheap out on the regulator. It is a task to get the pressure down to the 3-4 psi range and cheap ones claim they will but won't I used an Aeromotive Low Pressure High Flow...
    Liked On: 12-02-2024, 08:47 PM
    Posted On: 12-02-2024, 07:27 PM
  8. talos
    talos liked post by bobcowan On thread : Weber winter project
    Any IR intake system runs best with a cam that has a wide LSA and minimal overlap. Because there isn't a common plenum, the runners are subject to some pulsations as the valves open and close. If...
    Liked On: 09-25-2024, 05:35 PM
    Posted On: 09-25-2024, 03:54 PM
  9. talos
    talos liked post by MaSnaka On thread : A shout out for Brent Lykins
    I'm sure many of you have heard of Brent Lykins Motorsports. I had to replace the cam in my Cobra and went with Brent because the engine builder I purchased the short block from couldn't give me the...
    Liked On: 08-04-2021, 06:54 PM
    Posted On: 08-04-2021, 06:16 PM
  10. talos
    talos liked post by t walgamuth On thread : Chassis
    My VSE has an aluminum Monocoque with a cast aluminum subframe up front designed and built by the well known Engineer Herb Adams. Herb and Matt built about 25 cobras with the Monocoque chassis. ...
    Liked On: 06-21-2021, 11:44 PM
    Posted On: 06-21-2021, 05:30 PM
  11. talos
    talos liked post by 1ntCobra On thread : Chassis
    Kirkham has built 2 with billet aluminum frames that I am aware of. http://www.clubcobra.com/forums/kirkham-motorsports/85278-million-dollar-skunksworks-kirkham.html The first one was...
    Liked On: 06-21-2021, 11:44 PM
    Posted On: 06-21-2021, 10:50 AM
  12. talos
    talos liked post by 1985 CCX On thread : Which Air Filter
    Air filters? What are those ..... 😁
    Liked On: 05-16-2021, 12:19 AM
    Posted On: 05-15-2021, 12:54 PM
  13. talos
    talos liked post by incoming On thread : Please help with air filter breather combo
    Run it down the road once without a filter just to verify the problem.?
    Liked On: 05-01-2021, 10:47 PM
    Posted On: 05-01-2021, 07:15 AM
  14. talos
    talos liked post by blykins On thread : Need FE heads
    IMO, the Trick Flow head is simply the best out of the box FE cylinder head as of right now. I'm predominantly an FE builder and the TFS heads are just superb. Unfortunately, they are out of stock...
    Liked On: 03-30-2021, 08:33 PM
    Posted On: 03-30-2021, 09:06 AM
  15. talos
    talos liked post by CCKW353 On thread : Thanks to Lykins Motorsports (blykins)
    Typical Brent :). He did my 427 FE SO motor. He is still readily available to speak with when needed.
    Liked On: 11-27-2020, 02:29 PM
    Posted On: 11-27-2020, 12:39 PM
Page 1 of 2 1 2

All times are GMT -7. The time now is 06:14 AM.

Contact Us - Club Cobra Home - Archive - Top

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink