Club Cobra GasN Exhaust  

Go Back   Club Cobra > Members List


gjkrv8
CC Member

About Me

  • About gjkrv8
    City
    Melbourne
    State
    VIC
    Country
    Australia
    Cobra Make, Engine
    Classic Revival CR 3505, LS1, T56 6 Speed, VE 3.45 LSD Rear, 6 Spot AP Fronts, 4 Spot Wilwood Rears
    Engine type and displacement
    LS1 Gen III 5.7L
    Tranny type
    6 Speed Manual

Visitor Messages

Showing Visitor Messages 1 to 3 of 3
  1. velj
    01-15-2013 06:39 AM - permalink
    velj
    hi greg, love the colour, i recently just painted out cobra voodoo blue, but having trouble with the stripe colour, what did you do yours? i like the look of it, also what area are you in? im from northen suburbs of melbourne (macleod)
    once my post gets approved you can see some photos of it
    cheers
  2. gjkrv8
    08-28-2011 11:06 PM - permalink
    gjkrv8
    Hi Dave, Mine is tucked in at the back between the diff and the fuel tank. There is a hose that goes to the engine. There is a little solenoid on the engine that is switched on and off by the ECU. Its location was on the front passenger side of my engine. Not sure about the LS7 though. I am just running a single fuel line up to the engine. They seem to do this in all prod cars and dont have any heat/evap related issues. Also, I'd recommend using a brake padal light switch rather than the pressure switch Ian uses in the rear line. When I have my bias set to favour the front, the brake light takes a bit more pedal pressure to come on which is a little unnerving in traffic when you use a light foot to brake. Hope your build is going well. I think we'll have to organise a shed run when thet weather fines up. Rgds Gregg
  3. DaveW
    08-28-2011 10:58 PM - permalink
    DaveW
    Gregg,
    How are you, if you can remember, how does the carbon canister hookup, did you mount down the back (as per Manual), up the front, do i need to run a vacuum line down to the front, i'm putting in the brake and fuel lines and the manual doesn't give any clear indication about any other lines.
    Cheers, hope your well

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 03-10-2025 11:31 PM
  • Join Date: 04-11-2008

Likes Received

312 Likes
  1. letsboogie351
    letsboogie351 liked post by gjkrv8 On thread : Post the coolest picture of your car!
    http://www.clubcobra.com/photopost/data/500/medium/Cobra_PI_2017.jpg
    Liked On: 11-22-2018, 02:27 PM
    Posted On: 07-02-2018, 02:34 AM
  2. Ron61
    Ron61 liked post by gjkrv8 On thread : BJ's Pace 289 USRRC Build.
    Well done BJ, great work, car looked and sounded awesome. cheers Gregg
    Liked On: 10-02-2018, 04:49 AM
    Posted On: 10-02-2018, 02:57 AM
  3. BJ's Snake
    BJ's Snake liked post by gjkrv8 On thread : BJ's Pace 289 USRRC Build.
    Well done BJ, great work, car looked and sounded awesome. cheers Gregg
    Liked On: 10-02-2018, 03:01 AM
    Posted On: 10-02-2018, 02:57 AM
  4. Gav
    Gav liked post by gjkrv8 On thread : 25th Anniversary Cobra Nationals 2018
    You looking for a designated driver Gav? :-)
    Liked On: 08-15-2018, 12:04 AM
    Posted On: 08-14-2018, 10:50 PM
  5. Gav
    Gav liked post by gjkrv8 On thread : 25th Anniversary Cobra Nationals 2018
  6. Gav
    Gav liked post by gjkrv8 On thread : 25th Anniversary Cobra Nationals 2018
  7. Tenrocca
    Tenrocca liked post by gjkrv8 On thread : 25th Anniversary Cobra Nationals 2018
  8. boxhead
    boxhead liked post by gjkrv8 On thread : Broken A-Arm
    Thanks Andrew I think I get it now :-)
    Liked On: 04-17-2018, 10:05 PM
    Posted On: 04-15-2018, 07:02 AM
  9. boxhead
  10. Wazza
    Wazza liked post by gjkrv8 On thread : Beejay's New Cobra Build
  11. boxhead
    boxhead liked post by gjkrv8 On thread : Saul........AP #23
  12. guye
    guye liked post by gjkrv8 On thread : Anyone know a good fibreglass repairer?
  13. Aussie Mike
    Aussie Mike liked post by gjkrv8 On thread : Anyone know a good fibreglass repairer?
  14. Modena
    Modena liked post by gjkrv8 On thread : Anyone know a good fibreglass repairer?
  15. Gav
    Gav liked post by gjkrv8 On thread : Anyone know a good fibreglass repairer?

All times are GMT -7. The time now is 09:41 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink