Club Cobra - View Profile: Akimbeau

Akimbeau
CC Member

Last Activity: 08-09-2024 09:32 AM

About Me

About Akimbeau

Zip Code

91403

State

CA

Country

USA

Cobra Make, Engine

ERA 289 FIA 351Windsor

Visitor Messages

Showing Visitor Messages 1 to 1 of 1

02-21-2016 01:22 PM - permalink
BCJ

I just read your post about removing carpeting in an ERA FIA. I just bought a used FIA street car and have considered doing the same yet also had your concerns. Peter told me the guy can be messy but said it was all possible. Did you try it yet? I'm curious to see how it goes for you as there's not much going back!
- View Conversation

Statistics

Total Posts

Visitor Messages

Total Messages: 1
Most Recent Message: 02-21-2016 01:22 PM
Visitor Messages for Akimbeau

General Information

Last Activity: 08-09-2024 09:32 AM
Join Date: 04-05-2014

Likes Given

15 Likes

Akimbeau liked post by patrickt On thread : Hard Braking causing stalls.

... and you don't necessarily even need the plastic whistle. I use the little black Holley "Metering Body Vent Baffle" that you can see here in black. Part number 85-626. It works surprisingly...
Liked On: 03-08-2017, 10:57 PM
Posted On: 02-20-2017, 03:42 PM
Akimbeau liked post by Karl Bebout On thread : Steel Spinners...

Mickmate: looks like an opportunity for you to add another item to your well made product line and you could help fill a need for those that don't want to deal with either Shelby American or...
Liked On: 08-30-2016, 10:36 PM
Posted On: 08-30-2016, 09:22 AM
Akimbeau liked post by Al G On thread : Steel Spinners...

Those are identical to the spinners on my car. I often wonder why they say "American Shelby, Inc" and not "Shelby American, Inc."
Liked On: 08-30-2016, 08:11 AM
Posted On: 08-30-2016, 07:16 AM
Akimbeau liked post by davids2toys On thread : Aluminum Panel Refinishing

Not that I have tried this on the Cobra, but other aluminum I have, including my job. I would do as above but finish it off with the WHITE Scotchbrite. It is a great polisher
Liked On: 03-13-2016, 01:00 PM
Posted On: 03-13-2016, 08:51 AM
Akimbeau liked post by krausewich On thread : Aluminum Panel Refinishing

Nice advice above. I would not recommend going as low as 180 grit though. Even 220 may be a bit much. A fresh piece of 400 will do a great job for a bit. Work your corrosion areas lightly with the...
Liked On: 03-13-2016, 01:00 PM
Posted On: 03-12-2016, 04:39 PM
Akimbeau liked post by DanEC On thread : Aluminum Panel Refinishing

I coated my panels with Sharkhide when I assembled my car but at this time I would not recommend that you try any type of protective coating. Sharkhide is difficult and tricky to apply and doing so...
Liked On: 03-13-2016, 01:00 PM
Posted On: 03-12-2016, 02:34 PM
Akimbeau liked post by HTM101 On thread : Aluminum Panel Refinishing

Its helpful to use a straight-edge as a guide while scuffing back and forth with the piece of Scotchbrite. Something softer than the alloy, such as a scrap piece of wood; a half-round, a 1"x1", even...
Liked On: 03-13-2016, 01:00 PM
Posted On: 03-12-2016, 01:08 PM
Akimbeau liked post by MOTORHEAD On thread : Aluminum Panel Refinishing

Ditto the above.
Liked On: 03-13-2016, 01:00 PM
Posted On: 03-12-2016, 11:29 AM
Akimbeau liked post by 427Larry On thread : Aluminum Panel Refinishing

Use a Maroon ScotchBrite Pad with WD40, the WD40 has fish oil in it. Try to follow the original grain pattern direction in as long a strokes as you can, wipe off any excess WD40 when you are done, do...
Liked On: 03-13-2016, 01:00 PM
Posted On: 03-12-2016, 10:56 AM
Akimbeau liked post by Blacklemming On thread : What IS that?

Prepaid phone card ??
Liked On: 03-03-2016, 08:20 PM
Posted On: 03-03-2016, 12:47 PM
Akimbeau liked post by 68 Fastback On thread : What IS that?

Cut a wire and see what stops working or starts to smoke. :0
Liked On: 03-03-2016, 08:20 PM
Posted On: 03-03-2016, 12:49 PM
Akimbeau liked post by Bernica On thread : What IS that?

A remote engine shut-down device if you are trying to run from the cops!:LOL:**)
Liked On: 03-03-2016, 08:20 PM
Posted On: 03-03-2016, 01:10 PM
Akimbeau liked post by 55312 On thread : What IS that?

It's wired into the chronosynclastic infundibulum. Not to worry though, it looks OK.
Liked On: 03-03-2016, 10:58 AM
Posted On: 03-03-2016, 06:05 AM
Akimbeau liked post by Paul F On thread : What IS that?

It is a Homeland Security widget. You're on their list.
Liked On: 03-03-2016, 10:58 AM
Posted On: 03-03-2016, 10:39 AM
Akimbeau liked post by DustinJ05 On thread : New b & b project info needed

I used the Heidts Performance 5/8" for the front and my rims and tires are listed below. I've got a Ford 9" rear and just swapped from the factory set up to a 3.75 Posi. Also, a suggestion for the...
Liked On: 04-11-2014, 10:49 PM
Posted On: 04-11-2014, 10:05 PM

About Me

Visitor Messages

Statistics

Likes Given

Mini Statistics

Group Memberships

Recent Visitors