About Me
- About AC Ventura
- City
- North of London
- State
- UK
- Country
- UK
- Cobra Make, Engine
- AC Cars Limited, 302 EFI
- Ride
- Porsche 911 (1989)
Likes Given
36 Likes
-
AC Ventura liked post by patrickt On thread : Holley 750 vacuum/can I remove this?With a Holley 750 vac secondary, I can't emphasize enough how having the idle/transition circuits tuned just right can make a HUGE difference in your overall quality of life.;) Seriously, the...Liked On: 08-26-2020, 05:59 AM
Posted On: 12-09-2019, 08:34 AMAC Ventura liked post by RockBit On thread : Moroso 8 Qt oil pan...oil level re-verificationThe only way to verify your dipstick full mark is to drain the pan completely then add exactly 8 quarts of oil. Do not start the engine. Allow time for the oil to settle into the pan, then insert...Liked On: 10-17-2019, 03:18 PM
Posted On: 10-09-2019, 06:16 AMAC Ventura liked post by patrickt On thread : Tragic AccidentQuality components, and adherence to just basic good-mechanics, is pretty important. You don't have to be tracking the car, or even running her hard, to get in to a serious accident if you have a...Liked On: 06-29-2019, 03:00 PM
Posted On: 04-02-2019, 08:45 AMAC Ventura liked post by Gaz64 On thread : Dual radiator caps / coolant recovery linesJust run a higher pressure cap on the lower point. Then at that point, cap the recovery tube. The upper cap will then be always be the point of release into the recovery tank. Only the upper...Liked On: 05-26-2019, 11:59 AM
Posted On: 05-09-2019, 03:56 PMAC Ventura liked post by patrickt On thread : First start of the Pond 427 FE in-carI like that, turn the key, see if it blows up and, if not, check for leaks. Yep, after all these years I still do the exact same thing.:LOL:Liked On: 05-01-2019, 12:56 PM
Posted On: 05-01-2019, 12:04 PMLinks monetized by VigLinkAC Ventura liked post by cycleguy55 On thread : 427 Cobra hood scoopsSorry, that myth is refuted by this video: https://www.youtube.com/watch?v=XFdkLFvqbZY Worth noting is the surface area around the bottom and sides of the engine compartment are far greater than...Liked On: 04-05-2019, 04:38 PM
Posted On: 03-30-2019, 03:47 PMAC Ventura liked post by Frank Messina On thread : Help identifying QFT carb pleaseThat is a timed vacuum port that is not needed in your case since you are not running vacuum advance and should be capped off. It does nothing at idle but supplies vacuum when the throttle is opened...Liked On: 02-21-2019, 02:59 PM
Posted On: 02-18-2019, 04:54 PMAC Ventura liked post by Mark IV On thread : AC Mk IV...the general consensus?Brian loved to tell that story. 1) the time was WAY less. 2) The 427 bucks had been binned by AC so the MK IV was built on fiberglass forms that Autokraft built. They DID have the Ace, 289 and FIA...Liked On: 02-18-2019, 01:45 PM
Posted On: 02-17-2019, 06:05 PMAC Ventura liked post by dacobb On thread : AC Mk IV...the general consensus?Did Kim Kardashian design the rear end of that thing?Liked On: 02-15-2019, 05:01 PM
Posted On: 02-15-2019, 12:57 PMAC Ventura liked post by C5GTO On thread : Retrospective ceramic coating experiences ?I have ceramic coated headers and side pipes on my Cobra. I've been really happy with them, but not so much for temp reduction, but for good looks and protection from corrosion. The biggest heat...Liked On: 02-08-2019, 05:20 PM
Posted On: 02-08-2019, 10:32 AMAC Ventura liked post by BAsque1 On thread : Retrospective ceramic coating experiences ?I ceramic coated my headers, done by Firefly (Ron Roberts) and while I did not actually take any temp readings my best gauge is the co-pilot wifey. She used to complain that riding the car in the...Liked On: 02-08-2019, 07:10 AM
Posted On: 02-08-2019, 06:56 AMAC Ventura liked post by DanEC On thread : Retrospective ceramic coating experiences ?I have to admit to some skepticism also. My headers, primary pipes and mufflers on my under car system are all ceramic coated in black inside and out. My mufflers are Spinteck baffled mufflers (no...Liked On: 02-08-2019, 06:31 AM
Posted On: 02-08-2019, 05:14 AMAC Ventura liked post by patrickt On thread : Pond Fe:Verifying dipstickThis gets asked more than you think, and you can really complicate it in your mind if you start adding in the filter volume, the cooler volume, the tilt of the engine, etc. But, it's pretty easy. ...Liked On: 01-23-2019, 05:02 AM
Posted On: 01-22-2019, 05:14 PMAC Ventura liked post by RockBit On thread : Pond Fe:Verifying dipstickMy dipstick was a generic one with no marks. After I cut off the tube and mounted it, The stick would hit the bottom of the pan before it was full inserted. I measured and cut the dipstick so...Liked On: 01-23-2019, 05:02 AM
Posted On: 01-22-2019, 05:45 PMAC Ventura liked post by Ron61 On thread : Pond Fe:Verifying dipstickWhat Rock Bit did was the way I marked my dip stick. I did mark mine of both sides for the quart low and full marks. RonLiked On: 01-23-2019, 05:01 AM
Posted On: 01-23-2019, 03:36 AM
All times are GMT -7. The time now is 01:30 AM.





Likes Received