Club Cobra GasN Exhaust  

Go Back   Club Cobra > Members List
Reload this Page Backdraft1725's Profile
Portal Register FAQ Community For Sale Gallery Calendar Today's Posts


Backdraft1725
CC Member

Last Activity: 01-01-2025 08:00 AM

About Me

  • About Backdraft1725
    Country
    United States

Statistics

Total Posts
Albums
General Information
  • Last Activity: 01-01-2025 08:00 AM
  • Join Date: 05-21-2024

Likes Given

12 Likes
  1. Backdraft1725
    Backdraft1725 liked post by PDUB On thread : Weber carb balancing "Ah-ha" moment
    Pics to support the explanation please. Just for clarity, you use more than one term for idle set screw in your description. Are you intending that these are the same screw or screws at each point...
    Liked On: 10-31-2024, 05:31 AM
    Posted On: 10-27-2024, 10:41 PM
  2. Backdraft1725
    Backdraft1725 liked post by PDUB On thread : Weber carb balancing "Ah-ha" moment
    OK, thanks for the clarification! I am following you now. Which brings up another question for those in the know. I was under the impression, but not sure, that you only use one of the...
    Liked On: 10-31-2024, 05:31 AM
    Posted On: 10-30-2024, 03:14 AM
  3. Backdraft1725
    Backdraft1725 liked post by Gaz64 On thread : Weber carb balancing "Ah-ha" moment
    I have one idle speed screw as a positive stop ON EACH BANK. One screw on one side only encourages linkage wear/misalignment etc. Something to think about, for Weber IR owners. Gary
    Liked On: 10-31-2024, 05:30 AM
    Posted On: 10-31-2024, 03:29 AM
  4. Backdraft1725
    Backdraft1725 liked post by Gaz64 On thread : 48IDA fuel level and float height.
    The Main Well is in the middle of the bowl. Weber would have designed it this way, to be less likely affected by G force or angles. But with a choice for canted carbs, I would have the lines on the...
    Liked On: 10-03-2024, 05:09 AM
    Posted On: 10-03-2024, 03:13 AM
  5. Backdraft1725
    Backdraft1725 liked post by jolsen42 On thread : This gives ALL of us, a bad name Sheeeeeh....
    Actually Antonio is a pretty good guy, a little wacky at times but a good guy. John O
    Liked On: 09-27-2024, 01:47 PM
    Posted On: 09-27-2024, 01:34 PM
  6. Backdraft1725
    Backdraft1725 liked post by BezerBoy On thread : Shorter Length TKX Shift Lever Option?
    Here is an update. I am using the 1 inch offset White Lighting Shifter assembly. This helped me get the shifter from over the transmission to the side like the top loader. Not perfect, but close. I...
    Liked On: 09-02-2024, 11:40 AM
    Posted On: 08-30-2024, 06:00 PM
  7. Backdraft1725
    Backdraft1725 liked post by patrickt On thread : Stalling
    Had you just recently changed out your battery you would have mentioned it, so this is not likely to be your problem. But I'll post it nonetheless because there may be some guys out there that are...
    Liked On: 08-15-2024, 05:32 AM
    Posted On: 08-14-2024, 01:21 PM
  8. Backdraft1725
    Backdraft1725 liked post by indianamoon On thread : Sidepipe evolution
    Not nearly as flashyhttps://i.imgur.com/usoiyOh.jpghttps://i.imgur.com/qWMhJYD.jpg
    Liked On: 07-09-2024, 06:42 AM
    Posted On: 07-07-2024, 12:28 PM
  9. Backdraft1725
    Backdraft1725 liked post by FredG On thread : View under the dash.
    Yes. Regular drill bits and nice and sharp hole saws. Also, a lot of measuring and re-measuring.
    Liked On: 06-24-2024, 06:13 AM
    Posted On: 06-22-2024, 05:32 PM
  10. Backdraft1725
    Backdraft1725 liked post by CSX2345 On thread : Shelby Scarab Project
    Hello Everyone, Wanted to share my latest project in recreating the Scarab that Carroll Shelby drove and won at the Continental Divide Raceway in 1960. This would be Carroll's final first place...
    Liked On: 06-02-2024, 07:54 AM
    Posted On: 06-01-2024, 02:25 PM
  11. Backdraft1725
    Backdraft1725 liked post by Cashburn On thread : View under the dash.
    The "carbon" dashes from Iconic are fiberglass with a layer of carbon fabric on top. I have always used regular drill bits and hole saws. Make sure to cover the entire face with blue tape while you...
    Liked On: 05-23-2024, 08:11 AM
    Posted On: 05-23-2024, 08:04 AM
  12. Backdraft1725
    Backdraft1725 liked post by Tommy On thread : View under the dash.
    I haven't worked with carbon fiber, but I have with fiberglass. One trick is to start the cut by running the hole saw backwards so the teeth don't dig in. After it has worn a hole through the outer...
    Liked On: 05-22-2024, 04:30 PM
    Posted On: 05-22-2024, 04:23 PM

All times are GMT -7. The time now is 05:38 PM.

Contact Us - Club Cobra Home - Archive - Top

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink