Club Cobra Keith Craft Motorsports  

Go Back   Club Cobra > Search Forums
Reload this Page Search Results
Portal Register FAQ Community For Sale Gallery Calendar Today's Posts

Nevada Classics
Keith Craft Racing
Main Menu
Portal
Forums

Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
MMG Superformance
November 2025
S M T W T F S
            1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30            
Showing results 1 to 13 of 13
Search took 0.02 seconds. Search: Posts Made By: kvonbehren
Forum: 429/460 Engine Talk 01-19-2018, 09:22 AM
Replies: 9
Views: 971
Posted By kvonbehren
Excellent. Thanks for the help. I have a Canton...

Excellent. Thanks for the help. I have a Canton pan with kick outs so I think I'll run it without the cooler and watch the oil temp closely.
Forum: 429/460 Engine Talk 01-18-2018, 04:28 PM
Replies: 9
Views: 971
Posted By kvonbehren
It sounds like maybe I don't need the cooler....

It sounds like maybe I don't need the cooler. When I bought this car I assumed the cooler was hooked up but when I pulled the motor I found out it wasn't. The motor that's going in this car is over...
Forum: 429/460 Engine Talk 01-17-2018, 03:48 PM
Replies: 242
Views: 53,754
Posted By kvonbehren
545 ci

Just getting ready to install new 545 ci in a Mark 111. Just finished dyno so it should be installed next week. Motor made 717hp and 678 ft/lb torque @ 4200.
Forum: 429/460 Engine Talk 01-17-2018, 02:36 PM
Replies: 9
Views: 971
Posted By kvonbehren
Oil Cooler line routing for 460

This is probably a stupid question but here goes. I have a Superformance Mark 111 that came with an oil cooler that was not connected. I'm installing a new motor and need to know the correct routing...
Forum: Transmission Talk 12-26-2017, 02:18 PM
Replies: 2
Views: 440
Posted By kvonbehren
Excellent, thanks. I'm using a slave cylinder...

Excellent, thanks. I'm using a slave cylinder and bracket kit from Rosehill Performance. It was designed to work with tko/quicktime and a sbf but it looks like it will line up very well with the 385...
Forum: Transmission Talk 12-26-2017, 01:47 PM
Replies: 2
Views: 440
Posted By kvonbehren
NON-Hyd throwout Bearing for TKO 600

Getting ready to assemble a tko 600 with Quick time bellhousing to a 385 series BBF. I'm not using a hyd throwout so I need to know what the Ford part number is for a TOB. Everything I read says...
Forum: 429/460 Engine Talk 12-23-2017, 09:10 AM
Replies: 7
Views: 1,713
Posted By kvonbehren
460/tko 600

I'm currently putting a 545 with a tko 600 in my Mark 111 that originally had a 460 with 3550 tko using a 460 truck bellhousing. The new setup uses a quick time bellhousing. Everything fits great and...
Forum: Transmission Talk 12-09-2017, 09:04 AM
Replies: 45
Views: 3,340
Posted By kvonbehren
My car came with a 460 and 3550 big input tranny...

My car came with a 460 and 3550 big input tranny originally. I'm installing a 700+ hp approx 650tq 545bb and have already bought tko 600 w/.82 od. After talking to Cobra Valley guy I was told to...
Forum: Transmission Talk 11-17-2017, 08:04 AM
Replies: 13
Views: 1,049
Posted By kvonbehren
hinoonaz The torque rating for 3550 is...

hinoonaz
The torque rating for 3550 is 425Ft/lbs as Doggone states. My 3550 is the later one that has a 26 spline input/31 spline output shaft. I believe the early ones had a weaker input. I think...
Forum: Transmission Talk 11-12-2017, 11:04 AM
Replies: 13
Views: 1,049
Posted By kvonbehren
Thanks for the guidance.

Thanks for the guidance.
Forum: Transmission Talk 11-11-2017, 03:51 PM
Replies: 13
Views: 1,049
Posted By kvonbehren
Thanks. Could you get me a price on tko 600 with...

Thanks. Could you get me a price on tko 600 with the .82 overdrive. As for the 3550 it has 17k miles is it worth anything. I can call you next week if we should discuss over the phone
Forum: Transmission Talk 11-11-2017, 11:46 AM
Replies: 13
Views: 1,049
Posted By kvonbehren
Excellent Thanks for the help. One additional...

Excellent Thanks for the help. One additional comment my trans is the model 2600708 tko 3550 2 which I read has a 26 spline input shaft. It should take the same clutch as the 600, correct? Would you...
Forum: Transmission Talk 11-11-2017, 07:30 AM
Replies: 13
Views: 1,049
Posted By kvonbehren
Question TKO 3550 swap to TKO 600

I'm new to Club Cobra and this is my first time on the forum so please forgive if this question has been asked a million times.
I just bought an 01 Superformance Mark 111 which has motor issues...
Showing results 1 to 13 of 13

 

All times are GMT -7. The time now is 06:42 AM.

Contact Us - Club Cobra Home - Archive - Top

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink