Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Advertisers Forum (http://www.clubcobra.com/forums/advertisers-forum/)
-   -   Domed Filters for your TWM Injection (http://www.clubcobra.com/forums/advertisers-forum/101833-domed-filters-your-twm-injection.html)

Blittleton 01-02-2010 06:05 PM
Domed Filters for your TWM Injection
 
Here are the new Domed Filters that we are selling. Very nice product, get in non polished polished and anodizing. These are complete from the stacks and up. These are not cheap. This will give anyone who needs more clearance with there hoods. Please give me a call for more information at 859-630-9099. These filters are made for TWM,Webbers, Imagine Injection units.
http://www.clubcobra.com/photopost/d...ed_filter2.jpg
http://www.clubcobra.com/photopost/d...ed_filter3.jpg
http://www.clubcobra.com/photopost/d...ed_filter1.jpg

Excaliber 01-02-2010 06:26 PM
Eight tiny air filters for your sleigh... :)

LMH 01-02-2010 07:11 PM
I don't even have Webers and I'd love a set of those!!
Maybe a table center peice...hmmm.
Larry

csx4910 01-02-2010 07:26 PM
I can attest to the quality and fit and finish of these. I ended up with teh first prototype of these as no one else makes a proper filter that would fit under my csx hood with the 511 motor. Pricey yes, but absolutley beautiful. In the end I couldn't put a price on not sucking desert dust down those throttle bodies. I got mine in polished.
ron

StreetSnake 01-02-2010 07:27 PM
Very very nice. How much restriction do they have, or in other words how much hp lost. If I already didn't spend a small fortune on the roush ones you could sign me up. What is the going price? Beautiful

SoTxButler 01-02-2010 07:27 PM
Is that foam under the screen or some kind of fabric and is material sandwiched between two screens?

RodKnock 01-02-2010 07:33 PM
Those are very nice. I assume that they could also be anodized in satin black, semi-gloss black and gloss black?

Mando 01-02-2010 09:53 PM
Absolutely Beautiful!

Regards.

tkb289 01-02-2010 11:21 PM
The entire setup looks great ... bet it looks even better under the hood of a Cobra !

Blittleton 01-03-2010 11:22 AM
These have the same material as a regular filter. I know that the filter element has been tested on what hp loss there was, but these had the best results. I'm not sure on the numbers but I will inquire about it. Anodizing could be in any style you wish. Color of the element can be changed as well.

Bill

Kramer 01-03-2010 03:21 PM
Who can I contact about these filters?

Kramer

Blittleton 01-03-2010 04:54 PM
contact me tomorrow at 859-630-9099 ask for Bill.

Blittleton 01-05-2010 05:58 PM
Single place set of 8 billet hi flow filters with velocity stacks, screw top rings and black filters under stainless steel mesh. The filter material is a multiple layered cotton for high filtration.



Bill

Stentor 01-05-2010 09:13 PM
These look like the filters made by C. Cook Enterprises in Kentucky. They were mentioned in a thread about two years ago.

I talked to them a month or so ago, and am considering getting a set for my IDAs. They are a bit on the pricey side.:eek:

SF_SN888KE 01-09-2010 10:04 AM
Beautiful! So, it sounds like you replace your old stacks with a new set of stacks (pricy in itself) and the new stacks have a screw on top for the filters?

What effect will these new stacks have on tuning with the manometer? (unscrew the filter and good to go?)

Bill - What's the cost? :confused: I'm sitting down ... :eek:

Blittleton 01-09-2010 10:35 AM
You are correct about the stack are swapped out. small block start out at 1250.00. You may want the low dome or high dome. That is why I would like you to contact me. There are a lot of variables in your decision. My number is 859-630-9099

bill

SF_SN888KE 01-09-2010 05:53 PM
Is there any effect on tuning with a manometer? e.g. unscrew filter and manometer fits as usual?

Blittleton 01-10-2010 10:57 AM
It will be the same.

Bill


All times are GMT -7. The time now is 03:20 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: