Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   ALL COBRA TALK (http://www.clubcobra.com/forums/all-cobra-talk/)
-   -   Watts Linkage Installation (http://www.clubcobra.com/forums/all-cobra-talk/107721-watts-linkage-installation.html)

acmjg 11-17-2010 10:21 AM

Watts Linkage Installation
 
I have installed a watts linkage setup in my car that was made up by Nick Acton (Mickmate) that I learned about in this link:


http://www.clubcobra.com/forums/show...t=watts&page=3

My car is a homebuilt and he was able to look at some pictures and send me the stuff I needed to get the job done. Check out the pictures in this link:

http://picasaweb.google.com/planecra...at=directlink#

and a video of it running through its travel with the coilovers disconnected:

http://s350.photobucket.com/albums/q...t=MOV04917.mp4

http://lh5.ggpht.com/_F7pl2fHE4ys/TO...0/DSC04918.JPG

Nick is great to work with and as honest as they come. Heck, he sent me the stuff, then sent a bill. Very trustworthy.

Anthony.

You can contact Nick here:
Nick Acton
Acton Custom Enterprises, LLC.
33 Wildwood Drive
Holderness, NH 03245
(603) 279-0241 Shop
(603) 254-4105 Nick Cell
(603) 229-2218 Bonni Cell
www.actoncustom.com

1985 CCX 11-17-2010 03:35 PM

Nick is the man, if I still had my CCX it would have his 42 gallon tank and the Watts Linkage.... :)

azfordman 11-17-2010 06:13 PM

I wish I had the experience of before and after....but I had Nick install the watts before I ever drove the car. I can say after 2,500+ miles it is a great set up. When the petal is depressed, the back end squats slightly, the front end lifts quite a bit, and the car hooks up! I have run it through a lot of twisty roads, dips, etc. and it handles just as great on the curves as the straight a ways. I give Nick an A+ on this upgrade to my car. Mark

john chesnut 11-17-2010 06:22 PM

Nick, That is a great looking set up. Nice work. John

mickmate 11-18-2010 04:45 PM

Thanks guys, Anthony is quite a car builder himself. That is the first customer installed Watts I have supplied and it looks like it worked well in his frame application. So that's Anthony's and the CCX's. What else with a Jag rear can we get these into, Butler boys? The fixture can be reversed for mount points also so the front mount can be high and the back one low as long as they're all level to the bottom of the carrier.

LMH 11-18-2010 05:56 PM

Nice job Nick!
Larry


All times are GMT -7. The time now is 10:18 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: