Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   ALL COBRA TALK (http://www.clubcobra.com/forums/all-cobra-talk/)
-   -   Could use a little help dialing in the bellhousing (http://www.clubcobra.com/forums/all-cobra-talk/110217-could-use-little-help-dialing-bellhousing.html)

RestoCreations 04-18-2011 04:44 PM
Could use a little help dialing in the bellhousing
 
So i have everything set up and i just took my measurements.

Measurements were taken rotating counterclockwise if facing the bellhousing.

I set the dial indicator to 0 at the 12 o clock mark, then rotated-90 degrees counterclockwise 3 times

Readings

90 degrees= -.008
180 degrees= -.018
270 degrees= -.009

Obviously i need to go up a good bit, but what about left to right? Since they are both negative and almost the same, what do i do? Excuse me for being a bit slow concerning this matter. I find it very confusing.

xlr8or 04-18-2011 04:56 PM
Check this link:

http://www.hurst-drivelines.com/file...206-15-09A.pdf

DanEC 04-18-2011 07:10 PM
Quote:
Originally Posted by RestoCreations (Post 1123471)
So i have everything set up and i just took my measurements.

Measurements were taken rotating counterclockwise if facing the bellhousing.

I set the dial indicator to 0 at the 12 o clock mark, then rotated-90 degrees counterclockwise 3 times

Readings

90 degrees= -.008
180 degrees= -.018
270 degrees= -.009

Obviously i need to go up a good bit, but what about left to right? Since they are both negative and almost the same, what do i do? Excuse me for being a bit slow concerning this matter. I find it very confusing.
Your good laterally - right on. If I understand your measurements correctly you do need to move the bellhousing up as close to .008 inches as possible.

blykins 04-18-2011 09:53 PM
Chris,

I'm sorry I haven't been able to get back to you, it's been one of those days...

Is everything torqued down? I'd try it once again, I think maybe your dial indicator is either overtraveling or you hit a bump on the register bore.

mkassab 04-19-2011 09:50 AM
Quote:
Originally Posted by blykins (Post 1123562)
Chris,

I'm sorry I haven't been able to get back to you, it's been one of those days...
Brent... "it's been one of those days" !! You mean working on my BOSS 9 engine is stressing you out?

Hey everyone.... believe me, Brent is loving this Boss 9 build!!

Mark


All times are GMT -7. The time now is 10:23 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: