| blykins |
10-10-2011 10:57 AM |
Quote:
Originally Posted by Jerry Clayton
(Post 1155620)
Patrick
I don't need it to run it in an engine---I'll use it to check the fit of cam bearings that I install in FE engines--then I can put my prized .600 lift Nascar cam back on the trophy shelf!!!
Also since I used to fly B767 like Doug, I'll raise my bid to $75
|
HAHAHA.....
Atta boy Jerry! |
| Jerry Clayton |
10-10-2011 11:06 AM |
Don't you two have anything to do?
|
| patrickt |
10-10-2011 11:08 AM |
Quote:
Originally Posted by Jerry Clayton
(Post 1155625)
Don't you two have anything to do?
|
Not really. ERAChas is grilling burgers outside later though. We're both going to drop by and bug him.:cool: |
| ERA Chas |
10-10-2011 12:31 PM |
Quote:
Originally Posted by patrickt
(Post 1155627)
Not really. ERAChas is grilling burgers outside later though. We're both going to drop by and bug him.:cool:
|
Yours will be 'well done' - from that shagged white mop you love so much. |
| rodneym |
10-10-2011 12:37 PM |
Quote:
Originally Posted by ERA Chas
(Post 1155639)
Yours will be 'well done' - from that shagged white mop you love so much.
|
Bid on it, Chas!
That cam would make a nice rotisserie. :JEKYLHYDE |
| blykins |
10-13-2011 06:06 AM |
6 hours to go....
|
| patrickt |
10-13-2011 07:38 AM |
Since this isn't an auction site, sniping the bid will not be tolerated. If there is any semblance of dueling bids going on it will continue until the last man stands. I think the chances of that are slim, but right now Jerry stands to steal a very expensive cam for a mere $75.:cool:
|
| Jerry Clayton |
10-13-2011 09:53 AM |
And I got a lot of HP/race parts for $75----front motor plates, 7 or 8 alternators, oil bypass valves, radiators----$75 seems to be my magic bid $
|
| flaflier |
10-13-2011 09:58 AM |
How would that cam compare to a standard 282S Comp Cam?
Jim
|
| blykins |
10-13-2011 10:01 AM |
The 282S cam is a 236 duration at .050". This cam basically has 20 more degrees of duration, more aggressive lobes and higher lift.
The added duration would shift the hp/tq curves to the right by quite a bit. This would add top end (if the heads/intake will support it) and take away from the bottom end.
|
| flaflier |
10-13-2011 10:07 AM |
So, in a 454" HR, it sounds like that cam would work quite nice. I have waaayyyy more low end than I need now anyway, and since it's to a good cause, I will go 100.00.
|
| blykins |
10-13-2011 10:15 AM |
The cubic inches will help mellow the cam down....but it should be pretty fun.
|
| patrickt |
10-13-2011 12:03 PM |
Quote:
Originally Posted by flaflier
(Post 1156123)
So, in a 454" HR, it sounds like that cam would work quite nice. I have waaayyyy more low end than I need now anyway, and since it's to a good cause, I will go 100.00.
|
Looks like you got it. PM 767Jockey and get his address and send him a check for $100. Then PM Brent and tell him where you want your cam shipped to. Everyone's on the honor to do this in a timely manner. And I'll figure out a way to write it off as a charitable contribution.:cool: |
| RodKnock |
10-13-2011 03:10 PM |
Quote:
Originally Posted by patrickt
(Post 1156148)
And I'll figure out a way to write it off as a charitable contribution.:cool:
|
Bahahahaha. :LOL: |
| 767Jockey |
10-13-2011 04:57 PM |
Guys,
Thanks SO much for doing this, I'm very grateful and appreciative. I was able to pick up a set of heads that will need rebuilding. I'm going to ship them to Brent to get an overhaul. If it's ok with all you guys it's probably a good idea to leave the proceeds with Brent to apply to the final bill for the rebuilding of the heads. Does that work for you guys?
|
| patrickt |
10-13-2011 05:00 PM |
Quote:
Originally Posted by 767Jockey
(Post 1156202)
Does that work for you guys?
|
Works for me. Flaflier can just send the check to Brent. Maybe Brent will snap some shots of the work he does and we can then find fault with it and make fun of him.;) |
| blykins |
10-13-2011 05:02 PM |
Wow, what support I get from you guys.
|
| flaflier |
10-13-2011 05:27 PM |
Brent,
As an added bonus for doing this, if you want....
I recently harvested a 9'2" alligator, which provided 52lbs of gator tail.
I have it frozen in 2.5lb packages, and I can ship one package frozen overnight along with the check...
You game?
|
| patrickt |
10-13-2011 05:30 PM |
Fried gator is not bad. It gets even better with a little cajun twist thrown in to it. I don't know how cajun Brent is though.
|
| blykins |
10-13-2011 05:38 PM |
I can honestly say that I've never been offered alligator tail before.....LOL
Hey, if you're willing to ship it, I'm willing to try it. How's the best way to cook it? Just fry it?
|
| All times are GMT -7. The time now is 07:44 PM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
