| msinc |
11-16-2022 08:23 AM |
Jacks that wont damage a nice floor?????
2 Attachment(s)
What do all you folks out there use to jack up your cars that wont damage or scratch up a nice garage floor??? If there even is such a thing....I just recently had my garage floor redone with epoxy. It is pretty tough stuff and light scratches will come right out with a light polish and wax. I am worried about putting deep marks in it with jacks and stands, etc. What do you all do to help eliminate this??? Thanks in advance for reading this and any info!!!!! Attachment 38291
Attachment 38292 |
| sgianino |
11-16-2022 12:17 PM |
3/4" Plywood Scraps to the size you need under the Jack and Stands
|
| incoming |
11-16-2022 04:12 PM |
I concur.
|
| DanEC |
11-16-2022 04:23 PM |
Yes, squares of plywood, high density brown board, etc.
|
| Hapnyny |
11-16-2022 04:30 PM |
If you buy 2x6 and make 12 inch cuts you have the perfect base for a jack stand. I personal use Quickjack to get my Cobra off the ground. Takes me three minutes from start to finish. I own Good Year Billboards so they are always off the ground when I’m not running to avoid flat spots.
|
| Morris |
11-16-2022 06:26 PM |
|
| Sycraft |
11-16-2022 07:34 PM |
RV Jack Pads
|
| 767Jockey |
11-16-2022 07:41 PM |
I just use a 2'x3' piece of Masonite. Thin, light, easy to store and cheap.
|
| sgianino |
11-18-2022 05:25 AM |
I forgot about Masonite.....Yes!!
We use it to protect Hardwood floors and tile when working in customers houses..Good Stuff, available in 1/8" or 1/4"
|
| DanEC |
11-18-2022 07:24 AM |
I couldn’t remember the term Masonite. That’s what I meant by high density brown board. Even 1/8” thick Masonite provides adequate protection for jacks and Jack stands.
|
| Chicagowil |
11-18-2022 09:03 AM |
Also, look at the new 2' X 2' boards with rubber on them for basement floors. They are (I think) 1/2" ply with a rubber dimpled backing to keep the moisture out. I would think they would be a nice cushion and non-skid. Home Depot carries them in the plywood area.
|
| All times are GMT -7. The time now is 09:50 AM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
