|
I just got a tank in Pinal County and all of my fueling issues went away. As did the dieseling issuing that's developed. It's now un-developed. There's gotta be something funny with Maricopa County gasoline.
|
I think I am going to install an electric fuel pump to see if that makes a difference....I know I have talked to others who have had issues with the gas down here. Of course that is going to have to wait.....pushed the car pretty hard on the Arivaca run yesterday and busted the push rod on the intake valve of cylinder #2..... Looks like several of the push rods are wearing on the guides....not sure if it is the adjustment or if the guy who put the engine together used low grade rods. Will be picking up a set of hardened push rods in the next day or so.
|
You might also want to check the rocker arms and make sure they are the right ones for your motor. If the moment of leverage is too long or too short, you'll not only change the relationship, but the location of the push rod.
|
Quote:
just a thought. |
Azfordman,
sent ya a PM |
Note - I changed a blue Holley fuel pump for a blue Holley fuel pump last year and suddenly started blowing fuses. Called Holley, they said the newer blue models took more amperage, I had to install a relay. Just thought I would let you know. Good Luck...Posi........
|
Quote:
There is a difference between the two, with the Maricopa County fuel being blended for more oxygenization for smog control reasons. Possibly the MC fuel burns a little hotter?? Just a thought. |
FWIW, the builder of the engine did skimp and install low grade push rods. A couple of of local engine guys said this type of problem is normal when hardened rods are not installed. The push rod did not bend, the side wall was worn away until it snapped in half like a tooth pick. Should have a set of hardened rods by the end of the week.
http://i158.photobucket.com/albums/t...68/pushrod.jpg Just something to keep in mind when using roller rockers on a motor. Sorry if all of my issues have annoyed some of you here....in the future I will try not to bother you so much. Mark |
No bother at all Mark...at least not for me. I just have seen guys make a mistake like bending or breaking a pushrod and going back with hardened rods only to find out that they didnt have enough valve clearance in the higher rpm range. Then with the hardened push rods they really tore some stuff up.
How about your fuel/stumble issue....make any headway on that yet? Gene |
The car ran great on the Arivaca run.....but still did not "feel", if that makes sense, like it was performing at 100%. Once I get it up and going again I will try to find a performance shop that can perhaps tune it on a dyno. Again, with the 80's block, the 70's heads, and unknown compression ratio and cam specs, I am unable to set it up to manufacturer specs. I am sure that if the average Joe was driving the car it would be perfect, but something in my gut is telling me that she is not reaching her full potential.
|
Quote:
|
AZFord,
Just out of curiosity what do your plugs look like? If the motor is running lean from no fuel they will be nice and white, black and you might have issues in another direction, also a cheap way to diagnose issue with carbs.. WOW can't believe the last time I logged in was last December.... time fly’s**) |
Quote:
|
| All times are GMT -7. The time now is 03:08 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: