|
Warning label for dash
Hi there everyone.
Can someone please post a pic of the dash warning label for ICV advising of no crash test? I need to get one made and want to make sure I have the wording correct Also if you could include the dimensions. Thanks again. Here are some pics of heading toward rego trim. Aero screen with mirrors and correct seats in place. The seatbelts are labeled as ADR approved, not sure if I will get away with then as I though they needed to be retracrtable? http://i270.photobucket.com/albums/j...d/SDC13706.jpg And another http://i270.photobucket.com/albums/j...d/SDC13707.jpg And here are the side pipes, heat shields are rolled and ready to fit (will paint after test fitted) and the clamps on the pipes I will use to secure them (again will paint these heat proof black after trial fit). http://i270.photobucket.com/albums/j...d/SDC13704.jpg http://i270.photobucket.com/albums/j...d/SDC13705.jpg |
Hi Boxhead
So long as the belts are ADR complient and have the AS clearly labled they will be fine. Does your side pipes pass the noise test? Cant comment on the ICV placard as I didnt need one:D |
I too probably wont need one but figure for the $10 it will take to get one made it could save headaches later.
The car will go for noise test possably next week, along with emissions test and brake test. Depends if I get the heatshields finished off and the wheels back on. Did you get a costing from Jack yet? |
Boxhead,
My placard is on the firewall. http://www.clubcobra.com/photopost/d...0/P1020546.JPG Cheers |
Thanks very much Geoff, I realise you dont have easy access to your car right now but do you know roughly what the dimensions are?
|
No problem. Wish you'd asked a day earlier, arrived back in Saudi this morning :LOL: Looking at some other images the placard is approx half a stripe wide.
Cheers |
G'Day Boxhead. I'll try to send a pic of my labels that I have on my temporary rego dash. It is just a bit of printed paper stuck under a piece of clear contact. It will be replaced with a sticker in the door frame. The dimensions are 138 x 23 or 143 x 24http://www.clubcobra.com/photopost/d...thumbs/IMG.jpg
|
Trying again with the pic.[IMG]url=http://www.clubcobra.com/photopost/showphoto.php/photo/70446]http://www.clubcobra.com/photopost/data/500/IMG.jpg[/url][/IMG]
|
Third attempt... http://www.clubcobra.com/photopost/data/500/thumbs/IMG.jpg[/IMG]
Still no good I scanned the pic and it doesn't want to play |
G'day Boxhead. I have emailed you a Word Document I used for mine. I think I just cut it out as it printed and it was the right size. I just covered it in clear contact and stuck it on the dash near the middle.
Rgds Gregg |
Hi Boxhead
Jack's bill was $462 a bit less than I was expecting |
You mean like this one?
1 Attachment(s)
Hi Boxhead
I've seen one like this on a british car, cant remember where though.:JEKYLHYDE |
David,
I could have sent you mine... Ben |
I managed to make and fit the side pipe covers today before dropping a very heavy rock on my foot, if it is still sore tomorrow then I will go for an xray.
http://i270.photobucket.com/albums/j...d/SDC13725.jpg http://i270.photobucket.com/albums/j...d/SDC13727.jpg |
Alffie, I will give you a call on Monday, If you see Jack can you let him know I am keen to fly him down to Alice to do my inspection.
As I would prefer him over the new guy as I the new guy is an unknown quantity and I am not sure if he knows 100% what I am looking for, |
I hear that the Todd is in flow now?
My plates are the same as Geoff's http://www.clubcobra.com/photopost/d...ning_Plate.jpg http://www.clubcobra.com/photopost/d.../Mod_Plate.jpg Off for a drive! |
Certainly is, It has gone down alot overnight, but yesterday about noon it only had about 40cm to go before bursting its banks and flooding the town centre.
In the first 4 or 5 days of 2010 we had more rain than we did for all of 2009, and it has rained alot more since then. |
Dave,
My plaque has almost identical wording to Krait's only it's red with white lettering, but I think that's only a NSW stipulation. Downloaded a few pics of the car ready for Engineering, including the Warning Plaque and the daggy wheels and tires in case the Engineer locks it up. http://www.clubcobra.com/photopost/d...ace_Small_.jpg. http://www.clubcobra.com/photopost/d...ng_Small_1.jpg http://www.clubcobra.com/photopost/d...st_Small_1.jpg Baz |
| All times are GMT -7. The time now is 12:55 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: