Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Australian Cobra Club (http://www.clubcobra.com/forums/australian-cobra-club/)
-   -   SPF front number plate (http://www.clubcobra.com/forums/australian-cobra-club/65766-spf-front-number-plate.html)

richfergus 06-28-2005 10:33 PM

SPF front number plate
 
Cameron and Garrett
where have you put your front number plates? I was thinking of going plateless though was pinged for not having a front plate on another car recently. I couldn't see one in your gallery Garrett: did it blow off?
Richard::3DSMILE:

justbetter 06-28-2005 10:43 PM

Yep
 
Yep blew clean off..

Every time i've been pulled up the boys in blue are usually to busy putting out their smoldering trouser legs from the side pipes, i found it stops them looking at the front of the car.

Actually Brian ( CTC ) has some nice rubber / stainless mount that clip on to the front nudge bar.

Regards Garrett

Getting toey lad !

Cameron Parsons 06-29-2005 02:46 AM

1 Attachment(s)
I am using Bryan's clips, work well and I am told by a very reliable source that they are good for 130 Mph.... at least..




Cameron

TMK 2002 06-29-2005 03:32 AM

hahaha, how about you have a look at mounting the number plate the same style dad has?

It pivots to give "More flow over the radiator";)

We got the idea for it from 450KW:)

luke-44 06-29-2005 03:51 AM

FinishLine makes a nice set up - not sure if it will fit your plate size though. Anyway - here is the instal info...


http://www.clubcobra.com/forums/show...threadid=52790


Good luck. :)

richfergus 06-29-2005 06:16 AM

Yes Garrett, more toey than a Roman sandal. Bryan says the mother is fully dilated and pushing hard. A July baby is a possibility!
Todd, this reminds me of the rotating number plates on James Bond's Aston Martin. Flick a switch and the plate flips horizontal at 100km/h or so. Could be onto something here!
Richard**)

TMK 2002 06-29-2005 09:00 AM

Dads is on a rotating type bar, at speed, it rotates around... at 100km/h it is long gone.

Sloth 06-29-2005 10:57 PM

I used two rubberised "P" clamps over the front overider in same position as Cameron's above. Works a treat. Sending them to the Chroming shop soon. NSW front "premium" (black and white) plate is thinner than usual plate and i can adjust the angle to whatever.

Toe.


All times are GMT -7. The time now is 01:17 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: