|
Harrison Seats and Door Trims
Picked up my seats from the motor trimmer today. I am extremely happy :D with the finish, look and quality of the leather.
http://www.clubcobra.com/photopost/d.../P10107211.jpg http://www.clubcobra.com/photopost/d...m/P1010727.jpg http://www.clubcobra.com/photopost/d...m/P1010731.jpg regards Mick:D |
Bluddy nice Mick. Certainly like the alternate color pleats.
|
Seats
Thanks Les.
They are actually more grey in the flesh, they look a little lighter in the photos Mick |
Looks Sweet!
Ben |
Very nice Mick! They look great in the two tone colours. I have been very happy with mine so far. Comfortable and ... well they look the part. When is it all on the road?
Merv |
Quote:
Merv, hopefully not too long. The plan is to be all done by Christmas Mick |
Won't be long now Schipps.
A classy job Schipps. Nice narrow profile on the seats. What are the frames from?
Here in the south, our seat backrests have to be a minimum of 845mm from the seat cushion. That includes the headrest, but to comply with the height restriction, the maximum gap on the extended headrests can't exceed 50 mm Do you have that Reg., in Qld also? From what I can see with the pics, your seats would easily comply in NSW. Do your headrests extend or are they fixed? Congratulations Baz. |
Baz, the frames are made new by Warwick for the Cobra to meet ADRs and states' requirements. My engineers had all the paperwork re approvals. The head restraints (from a Toyota) can be removed in a second, for example to fit a tonneau without having to have 'pockets' for them. They can be adjusted to any height. I had my seats trimmed at very reasonable cost. I liked them because of the lack of a high fixed back and also because you can sit low in them.
Merv |
Quote:
Do you have the same seat height requirements in Qld as we do? Baz |
I am not sure Baz but I believe that these aspects are the same. Other may comment. These seats have no runner either (one could be fitted, however). They bolt straight on to the chassis rails. I wanted my eyeline to be well below the top of the 'screen!
My bolster on mine is 825 (or thereabouts) above the floor level. Merv |
In NSW the drivers seat has to be adjustable (have a runner) for rego at least. Seats look good Mick - Are they assymetrical for better fit?
|
Interesting! Would be easy to fit but raise the seat height. They are made for RHS and LHS separately.
Merv |
Seats
Thanks guys for the comments.
Merv, thanks for answering those questions, I have been out sitting in the seats in the Cobra...Mmmmmmmmm, can't wait! |
Seats
They look hot......
STIFFY |
| All times are GMT -7. The time now is 04:10 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: