|
Need Help! Stewart Warner Tach!
Hey Guy's! I need a Stewart Warner Tech. I have one but it's not an electrical one.
I need the SW-82163 Tachometer RPM x 1000 (A) 0-8,000 rpm 3 3/8" Electric, 4-, 8-, 12-Cylinder . Black face and chrome Bazel. Please if you got one ...how much to take it off your hands! Thanks. Snake/Gerry. P.S. Do you need anything to go with it.....like a sender...I have no idea...this is my first dash wiring job. |
I have a full set of new-in-box VDO Cockpit style (black face, black bezel) gauges for about what you'd probably pay for the SW tach. Speedo is 160MPH, 3 3/8" mechanical. Tach is 7000 RPM, 3 3/8" electric, water, oil, volts, & fuel (GM 90 ohm) are 2 1/8". They're available because I didn't use them. Used Autometer 5" Sport Comp speedo & tach, and Z Series smaller gauges instead. Make me an offer.
|
Jegs, or Summit should carry them, and no, you wont need a sensor for it. It just hooks into the distributor, or an MSD box if your using one.
If you can't find what you want through them, let me know, I can order it directly through SW for you. DV 300 Cobras is NOT enough! |
DV
Thanks Buddy! I have a Holley HP Annihilator ignition system...I guess when I get an electrical tach I could conect it too that. Got another question for you.
After you hook up the steering colum to the wire harness...will the lights and the controls work? Because in the manual when you start hooking up the dash..there is wires to hook up the ignision switch, lights, wiper system etc? Do I just forget about them....and for some reasion...the red light on the dash has only one wire conected to it? So many question?? Sorry about that! Snake/Gerry. |
Snake,
When your dash is done you will have a large flat gray plug, and a large flat black plug. Both of these plug into the fuse box. Then you will have power to all systems...assuming you have the Column plugged in. DV 300 Cobras is NOT enough! |
DV
In the manual when you start hooking up the dash..there are wires from the wiring harness to hook up the ignision switch, lights, wiper system etc?
I'm using the GM steering colum to control my lights, wipers. What do I do about the wires for the ignistion switch, lights, wiper system from the harness? Do I just forget about them?, Cut them? tape them? Heat shrink them! For some reasion...the red light on the dash has only one wire conected to it? Did I miss something? Snake. |
I will look and see If we have a SW
|
Brent
Brent...Could you please delete this.
|
| All times are GMT -7. The time now is 11:23 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: