|
Can't Find Engine Mount??
Does anyone know where to get a LHS Engine Mount for a SBF (302) CRL?? I found this NAPA part number (6021639) going through the old postings but the frame side attachment is different than what I have. My frame side is a clevice or cannon bracket with a single Fore/Aft thru-bolt. The aforementioned NAPA part has two vertical studs for the frame side attachment. Can anyone make a suggestion??
Thanks, Dave F |
Check that NAPA number again, I think I used that on my Boss. One stud side has a pimple on it to orientate in the mount. I have plates for mounts and they drop over the studs pointing up.
There is a NAPA store in Troy, I can not remember the exact location. Check their web site. The guy there was pretty reasonable about letting me look at a few things before I paid for mine. Good luck. |
Anchor #2316 is what you are looking for.
Purchased at Kragens $12.95 Good quality and has a through bolt to prevent separation too. Rick |
Dave, it sounds like you have the Ford mounts. These were only available from Ford. The new mount which is from a Mustang GT are different. The Part# for the Ford mounts are D7ZZ-6038-A for the left side and D7ZZ-6038-B for the right side. Ford no longer makes these mounts but they are still in the system if the dealer will search for them. There is no aftermarket replacement that I know of.
Don |
Don, that is what I'm beginning to find out.
The gentleman with the posting on this subject previous to your response may well be my savior... I do not have his recomended parts stores in MI, but I found his part ## online and the picture looks very much like the mount I have to replace, if you have time check it out: http://www.partsamerica.com/PartDeta...artNumber=2316 Thank You All for the Responses... Dave F. |
NAPA part #602-1151 are a replacement for D7ZZ-6038A and B. I bought them at the local NAPA store for $13.33 A PIECE. (WEB SITE HAS THEM ABOUT .50 CENTS CHEAPER, BUT THEN YA GOTTA PAY SHIPPING). They seem to fit fine, although all I have done so far is test fit. Thanks, Earl
|
Earl, just got back from NAPA, the part that you recomended will fit ($14.99). The big difference between what I have on my CRL now and the NAPA part I just bought is the (over-travel) restraint pin. All US automobile manufactureres have a "severed elastomer" test to verify that if the rubber fails the additional motion will not cause harm to the vehicle or occupants (GM was sued in the 60's because a failed mount caused the throttle linkage to stick in the WOT position). I think if the new part failed, my side pipe will become the over-travel restraint. I'm gonna wrap a cable or two around the mount just in case.... Thanks!
Dave F |
Are these the mounts your looking for?
http://www.f150online.com/galleries/...26175&anum=313 I'm not using them. I had them mounted in the chassis but I decided to switch to the new mounts. If any one wants them drop me an email brandon.flood@gm.com |
| All times are GMT -7. The time now is 09:11 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: