Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Consumer Watch (http://www.clubcobra.com/forums/consumer-watch/)
-   -   David Kee Transmissions (http://www.clubcobra.com/forums/consumer-watch/48646-david-kee-transmissions.html)

weekendwarrior 12-31-2003 11:09 AM
David Kee Transmissions
 
Bought a Toploader from David, Just wanted mention that David was very professional and the work was first rate. Very easy to go Online and order additional small parts needed in the build.

Thanks David

ENTDOC 12-31-2003 12:13 PM
I need to order one also.What exactly did you get. chuck

weekendwarrior 12-31-2003 01:07 PM
I got a TL with a Mustang tailhousing (I believe 14"), wide ratio gears, 1 3/8 input, 31 spline output, reverse speedometer gear (so I did not need the adapter). Told him I needed it for a Kirkham 427. Came UPS bolted into a stout returnable shipping container.

P.S. David will also need to know if you are going to use a hydraulic throw out bearing or a clutch fork. I am running a clutch fork and slave cylinder.

Gary

PatBuckley 12-31-2003 01:14 PM
Gary -

What rear gear are you going to use? I am using a 3.07 and am out of luck in being able to get the right drive/driven combination when I use the reverse driven gear.

Pat

weekendwarrior 12-31-2003 01:48 PM
Pat I have the 3.31's that came with the car. I have given up the idea of getting everything to my liking the first time around. The goal is to get it Registered and then tinker and fine tune as I learn. It's going to howl on the highway but what the ____.

I was told 3.31 would be ok with the reverse speedo gear - hope so.:rolleyes:

Gary

Specialk 12-20-2004 07:58 AM
Gary,

I am building a Kirkham right now with a 3.31 rear gear. I am getting a DK Toploader with the reversed "drive" gear. Did you use a standard Ford gear? If so, what color or tooth count gear did you use? Will a standard rotation gear mesh with the reversed drive gear?

Enough questions for ya? **)

weekendwarrior 12-22-2004 04:17 PM
Quote:
Originally posted by Specialk


Gary,

I am building a Kirkham right now with a 3.31 rear gear. I am getting a DK Toploader with the reversed "drive" gear. Did you use a standard Ford gear? If so, what color or tooth count gear did you use? Will a standard rotation gear mesh with the reversed drive gear?

Enough questions for ya? **)
Kris,

I need now what you are asking, sent an email to DK, no answer, will call tomorrow

Gary


All times are GMT -7. The time now is 04:12 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: