Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Contemporary Classic Forums (http://www.clubcobra.com/forums/contemporary-classic-forums/)
-   -   Replacement wiper blades (http://www.clubcobra.com/forums/contemporary-classic-forums/145407-replacement-wiper-blades.html)

mrmustang 11-22-2021 08:18 AM
Replacement wiper blades
 
Ok, it's been quite awhile since I've had to replace a set of wipers. However, with my CCX now up for sale, I've been going over the smaller details so that the potential new owner will have very little, if nothing to deal with in order to enjoy the car once they have it licensed and titled.


So, what do I replace the wipers with, if my memory is correct, I believe these were sourced from a TR3, maybe a 1960, but not 100% certain.

Anyone recently replace theirs?

Thanks in advance,

Bill S.

patrickt 11-22-2021 09:59 AM
Quote:
Originally Posted by mrmustang (Post 1499772)
Ok, it's been quite awhile since I've had to replace a set of wipers. However, with my CCX now up for sale, I've been going over the smaller details so that the potential new owner will have very little, if nothing to deal with in order to enjoy the car once they have it licensed and titled.


So, what do I replace the wipers with, if my memory is correct, I believe these were sourced from a TR3, maybe a 1960, but not 100% certain.

Anyone recently replace theirs?

Thanks in advance,

Bill S.
They are bound to be either 8" or 9" and either spoon or bayonet fittings. Put a ruler on them and check the length. FWIW, mine from ERA are GWB164 9" Bayonet fittings and fit MG Midgets. Here's a nice page with pics to help you out:
https://www.holden.co.uk/c/hardware/...-blades/page/2

mrmustang 11-22-2021 10:43 AM
Quote:
Originally Posted by patrickt (Post 1499775)
They are bound to be either 8" or 9" and either spoon or bayonet fittings. Put a ruler on them and check the length. FWIW, mine from ERA are GWB164 9" Bayonet fittings and fit MG Midgets. Here's a nice page with pics to help you out:
https://www.holden.co.uk/c/hardware/...-blades/page/2

9" spoon it is, thanks.

Bill S.

Mark IV 11-22-2021 10:54 AM
Bill,

We have 9" and 10" spoons in stock

mrmustang 11-22-2021 11:06 AM
Quote:
Originally Posted by Mark IV (Post 1499778)
Bill,

We have 9" and 10" spoons in stock
Rick,

Thanks, already have a set incoming later this week. :)


Bill S.


All times are GMT -7. The time now is 09:17 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: