Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   FE TALK (http://www.clubcobra.com/forums/fe-talk/)
-   -   Need 427 Oil Pick-up Gasket P/N (http://www.clubcobra.com/forums/fe-talk/42780-need-427-oil-pick-up-gasket-p-n.html)

msinghof 06-24-2003 08:59 PM
Need 427 Oil Pick-up Gasket P/N
 
Is the oil pick-up tube to pump gasket a common Ford p/n? Have a 65 C5AE-A 427 top oiler and in the process of replacing the oil pan gasket I had to remove the oil pick-up screen and windage tray. This is the small diamond shaped gasket with two mounting bolt holes and one center hole. Appreciate any input. Thanks!

Softec 06-25-2003 07:38 PM
msinghof,

The cork pan gasket I just installed had the oil pump and pickup tube gasket included in the set. Victor Reinz #OS30764

RICK LAKE 06-29-2003 05:41 AM
msinghof Hi go to your local auto parts store and get a piece of gasket paper (fiber) and make your own. Outline the part on the paper and cut on the lines. Use a razor blade. It should take you about 5 minutes to make. Good Luck. Rick Lake

msinghof 06-29-2003 09:08 PM
Replaced All Gaskets...Still Leaks
 
Thanks for the input. Felpro makes cork pan gaskets and their product also includes the pump pickup gasket. Anyways, the application requires two pan gaskets with the windage tray and the end result is...still leaking at the bolts. I think my mistake was running the bead of RTV to the outside of the bolt holes instead of the inside. Will try it one more time.

cobra427hp 06-29-2003 10:44 PM
Be sure you are not using too much tork on the bolts and that your pan bolt holes are indented as both of these will cause leakage. The tork on the bolt holes is only about 10 lbs. I usually make a loop all the way around the bolt holes with silicone.

RICK LAKE 07-03-2003 03:59 PM
msinghof You are using the wrong RTV to seal an oil pan. Get spray Hi-Tack, and clean both surfaces with brakekleen. tighen bolts to 15 inch pds. and let dry overnight. Fill with oil and road test. Do you have a PCV valve on your motor?? If the motor builds up to much pressure inside, you will keep blowing gaskets until you get the pressure problem under control. Rick Lake


All times are GMT -7. The time now is 11:11 AM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: