| redchief |
10-03-2014 08:12 AM |
Stack Injection for Coyote 5 Liter Engine
Here is a sneak preview of an Injection System for your Coyote 5 Liter engine. It has a computer system that controls all the engine capabilities including the variable camshaft timing. After two days of extensive engine dyno at a high end shop, the initial results are 435 hp and 385 Ft Lbs of torque. The good news is that the torque curve was raised 1100 rpm. The engine is in a Factory Five Type 65 and just recently completed several shake down runs at PIR. Plans are to sell system or complete engine ready to drop into your vehicle. This will include new engine, stack injection, fuel system, computer and harness. Keep tune for more information.
http://www.clubcobra.com/photopost/d...s/img_3566.jpg |
| PLDRIVE |
10-03-2014 01:41 PM |
I sure hope he did not Dyno with those filters. :CRY:
|
| Bill D |
10-03-2014 02:55 PM |
Sweet!
|
| Gaz64 |
10-04-2014 01:15 PM |
Very nice, but it needs a filtered airbox rather than those restrictive screens.
Will make more power.
|
| redchief |
11-02-2014 05:36 PM |
Sema
Any of you going to SEMA, stop by booth 20230 and say hi. We will have the FF type 65 with the Coyote engine and our EFI stack injection at the booth.
|
| Horseracejudge |
11-06-2014 04:11 PM |
Ford Motorsport SVO plaque
1 Attachment(s)
Can anyone identify the plaque plate on this manifold. I've searched and can't find anything. It is on a 302 powered 2002 B & B build. B & B didn't do the engine. The plaque is integral to the casting. It wasn't added. It can't be removed. I'm the third owner. I'm sorting out the various components used on the build. Any info on the EFI is helpful. Thanks, Nick Attachment 24612 |
| damage |
11-06-2014 05:56 PM |
Quote:
Originally Posted by Horseracejudge
(Post 1325036)
Can anyone identify the plaque plate on this manifold. I've searched and can't find anything. It is on a 302 powered 2002 B & B build. B & B didn't do the engine. The plaque is integral to the casting. It wasn't added. It can't be removed. I'm the third owner. I'm sorting out the various components used on the build. Any info on the EFI is helpful. Thanks, Nick Attachment 24612
|
Looks like 94/95 Mustang plenum. |
| lovehamr |
11-07-2014 11:29 AM |
Chief, love the weber look but gotta loose those rubber hoses man!
|
| Horseracejudge |
11-07-2014 04:09 PM |
Damage, Thanks you. I'll check it out.
|
| All times are GMT -7. The time now is 03:01 AM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
