Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Holley Tuning (http://www.clubcobra.com/forums/holley-tuning/)
-   -   Holley throttle plate for list 3300 (http://www.clubcobra.com/forums/holley-tuning/132890-holley-throttle-plate-list-3300-a.html)

crenbbf 04-09-2015 10:54 AM
Holley throttle plate for list 3300
 
Hi All

Looking for a bit of advice as to where I can get a replacement throttle plate
assembly

I have problems with fuel leaking out along the primary shaft when the squirters are used.

I've been in contact with Carl's Ford parts but he's out of stock.

thanks

DanEC 04-10-2015 05:23 AM
If you can't find a replacement just about any of the restoration shops for carburetors could install bushings on your throttle shafts to tighten them up. If you can find a kit it's not even out of the realm of a do-it-yourself project. I had a Holley completely restored by the Holley Restoration shop years ago and it came back looking like a brand new carb.

joyridin' 04-10-2015 05:51 AM
I have sent a few Holley's to QuickTime and they will rebuild it/fix whatever you want. They made my carb look like it came out of the box. Actually, a lot better looking than when it came out of the box from Holley.

crenbbf 04-11-2015 08:32 AM
Thanks Guys

It would cost me a fortune to ship over to Kentucky and back.

However most of the problem seems to be fuel bowls set to high and fuel dripping on to the shaft and running off the end.

A bit of adjusting seems to have solved the problem.

cheers

Gaz64 04-12-2015 02:33 AM
You would probably find the shaft to body clearance is a little worn, nearly every Holley suffers from that, poor design from day one.

Better off getting the body fitted with bronze bushes, at least on the primary side.

Carb Junkys (ebay) sells a kit with a 3/8 piloted reamer and bushes to suit.

crenbbf 04-12-2015 04:10 AM
Quote:
Originally Posted by Gaz64 (Post 1344842)
You would probably find the shaft to body clearance is a little worn, nearly every Holley suffers from that, poor design from day one.

Better off getting the body fitted with bronze bushes, at least on the primary side.

Carb Junkys (ebay) sells a kit with a 3/8 piloted reamer and bushes to suit.
Cheers Gary


All times are GMT -7. The time now is 06:55 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: