-
Shop Talk
(
http://www.clubcobra.com/forums/shop-talk/)
| 392cobra |
04-05-2007 08:33 AM |
Good info Dave,thanks.
Dumb question : Wouldn't you still be trying to draw thru 3/8" ? I think I'm misunderstanding something.
|
| Nor Cal Al |
04-05-2007 08:53 AM |
I went with the Holly 110gph mechanical on my 392W because I could not find a place I liked to mount an electric. On the BDR there isn't much room between the tank and other interferences to mount, let alone get a drill in there. I believe the wiring for their pump goes to the right wheel well opening. Did not want it there.
Hey Wayne, I'll be down in /Brawley/El Centro this coming week......Can you turn down the temp a bit?
AL
|
Quote:
Originally Posted by 392cobra
Good info Dave,thanks.
Dumb question : Wouldn't you still be trying to draw thru 3/8" ? I think I'm misunderstanding something.
|
3/8" pipe is different from 3/8" tubing.. Pipe's measure ID (inside diameter), tubing's measured OD (outside diameter). The 3/8"MPT x 8AN fitting will give you full flow for your 8AN/1/2" system. You'll be fine.. |
| WildBill3 |
04-05-2007 12:28 PM |
not electric here
were feeding a holley 830hp with a mechanical holley hv off a 1/2" line works great no problems we did redo the airbeeds after install runs great and very simple,i like that:D
|
| Michael C Henry |
04-05-2007 08:38 PM |
Way over kill two Carter electric 15 psi 100 gal per hour pumps Y'd together with check valves to stop back feed. Seperate switches and indicater lites to tell if they are on.
|
| 392cobra |
04-11-2007 05:51 AM |
Quote:
Originally Posted by undy
3/8" pipe is different from 3/8" tubing.. Pipe's measure ID (inside diameter), tubing's measured OD (outside diameter). The 3/8"MPT x 8AN fitting will give you full flow for your 8AN/1/2" system. You'll be fine..
|
Thanks for the good explaination to my dumb question.:) |
| Dan Stryffeler |
04-11-2007 05:57 AM |
Running the Holley red pump, (on my second one) - the only reason I put in an electric one was that Everett-Morrison has a provision for one in their stock wiring harness.
I'm not entirely comfortable with it since it doesn't currently have any type of oil pressure cut off switch. Will probably change to a mechanical pump this year.
- Dan
|
| All times are GMT -7. The time now is 06:29 AM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
