Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Small Block Talk (http://www.clubcobra.com/forums/small-block-talk/)
-   -   Redline for Ford racing crate engine (http://www.clubcobra.com/forums/small-block-talk/128355-redline-ford-racing-crate-engine.html)

Mole21401 03-28-2014 01:58 PM

Redline for Ford racing crate engine
 
Have a new Backdraft Cobra with a Ford Racing crate engine.302/345 hp.Tach shows no redline.Any advice appreciated!

Dwight 03-28-2014 03:11 PM

a wild guess would be 5800 to 6000. 5.0 Mustang motor are limited at 6250.
A dyno chart of your motor would tell you.

I had a 302 in my Cobra for years and spun it to 6250 all the time.

Dwight

MFE III 03-28-2014 04:00 PM

this would seem to indicate 6,000 rpms would be safe, but the power starts to drop off above 5,500.
X302/340 HP CRATE ENGINE WITH CARB, INTAKE AND DISTRIBUTOR -- M-6007-X302D

bobcowan 03-28-2014 08:26 PM

Your redline really depends on two components: Camshaft, and valve train.

Your engine has hydraulic roller lifters, and matching valve train components. Those lifters are good for just a hair over 6,000.

The camshaft has a specific power band, where it makes the best power. You want to shift gears as the engine is falling off the back side of the power curve, so as you up shift and step on the gas, you'll be making enough torque to push the car along. Continuing to run the rpm's up after the cam stops making power is often pointless.

You'll have to look at the cam specs and see what kind of power band you have.

Mole21401 03-29-2014 04:31 PM

Thanks for the help,everybody.5500 is tops for my type of driving.The 302,with the gearing,really winds up quickly.I can definitely sense when it is up on the cam.one reason for my question stems from the tach which is defective(hits @ 3200 and just flutters).Backdraft will take care of it during the 500 mile service.So far,they have been fantastic and expeditious sorting out a few niggling problems.I highly recommend them to anyone waiting to decide upon a Cobra!

Z-linkCobra 04-03-2014 12:02 PM

Stand on it until she floats the valves....then grab another gear...lol.

CobraEd 04-03-2014 12:32 PM

and a third critical component
 
Quote:

Originally Posted by bobcowan (Post 1293050)
Your redline really depends on two components: Camshaft, and valve train.

Your engine has hydraulic roller lifters, and matching valve train components. Those lifters are good for just a hair over 6,000.

The camshaft has a specific power band, where it makes the best power. You want to shift gears as the engine is falling off the back side of the power curve, so as you up shift and step on the gas, you'll be making enough torque to push the car along. Continuing to run the rpm's up after the cam stops making power is often pointless.

You'll have to look at the cam specs and see what kind of power band you have.


The bottom end! If the top end is all built out to run to 7,000, but the crank and rods are all original cast iron pieces, you might want to re-think how high you want to run it.


.

dallas_ 04-03-2014 03:30 PM

If it is a Ford Racing crate motor, get the number off of it and look it up on the Ford Racing website. That should give you all the specifics of that motor.

Competition Crate Engines, Competition Mustang Engines, Competition Drag Racing Engines, Competition Stock Car Engines, Competition Funny Car Engins, Competition Racing Engines - Ford Racing Performance Parts

Mark IV 04-03-2014 05:44 PM

Rev it till it blows and then back it down one hundred............


All times are GMT -7. The time now is 04:09 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: