Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Tech Tips (http://www.clubcobra.com/forums/tech-tips/)
-   -   Trunk emblem location? (http://www.clubcobra.com/forums/tech-tips/39040-trunk-emblem-location.html)

Rodney 02-25-2003 10:23 PM
Trunk emblem location?
 
Hey guy's was wondering if some one could give me the measurement for locating the (1 7/8") round snake emblem on the trunk? I think the ERA building instructions give these measurements most accurately, or if an original cobra owner could take a measurement that would be great! Thanks in advance.;)

cslithergo 02-25-2003 11:34 PM
here is an old thread link from Bob Putnam but its no good. Bob can you help again? Your input and pictures have saved me a lot of trouble so far.

Thanks,
Chris

http://www.erareplicas.com/427/emblems.gif

cslithergo 02-25-2003 11:42 PM
little work but try this

http://www.erareplicas.com/freeman/427.pdf

go to page 106

this is Bob's manual.... just to give credit

Rodney 02-27-2003 08:37 PM
No diagrams?
 
Went to page 106 of the manual, and my acrobat reader will not open the diagrams. Could someone explain where these trunk emblems go? Thanks guy's. :JEKYLHYDE

Bob Putnam 03-03-2003 07:18 AM
Those free manuals don't have most of the illustrations. We gotta make money somewhere. :rolleyes:

The emblem locations

Rodney 03-03-2003 08:17 AM
Great!
 
Thanks Bob, I purchased a manual from you guy's a few years ago and have since given it away to a friend. Thanks very much for the diagrams!:D

cslithergo 03-03-2003 06:24 PM
Bob,
Thanks again. The next Cobra comes from you!
chris

Bannon 03-03-2003 08:02 PM
What do you use to stick the emblems to the car? My emblems have the pins to fit in the holes to keep it aligned but nothing else to actually hold them on.

Thanks,

John

Rodney 03-03-2003 10:31 PM
Fasten emblem
 
Hey John, if you have an SPF, set your pilot hole drill bit and 1/8" drill bit to the depth of the emblem pins only, (you could wrap some tape around the drill bit as a depth gauge) the trunk (boot) is pretty thick and you could avoid unsightly holes on the underside of the trunk. I'm researching some adhesives and will let ya know what works best. RTV maybe? %/


All times are GMT -7. The time now is 01:26 AM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: