Trouble engaging 5th (Doug Nash / Richmond 5sp)
I've had trouble getting into reverse since taking ownership of this vehicle earlier this year, but recently I've started having problems engaging 5th gear as well. Is this maybe just a matter of needing to adjust the shifting stops, or something more involved?
Thanks! |
Quote:
|
Does it grind going into reverse?
For trouble shifting into 5th, I agree adjusting the shifter and stops is pretty easy. If you Utube it will come up. I can give you the run down if you can't find it. When the shifter is adjusted correctly let us know if it is fixed or if the shifter was even a problem. 5/R share the same shifting fork in that transmission. It could be a bent or damaged shift fork, but don't think about that yet. I have never driven a car with a Doug Nash/Richmond. Can you shift quickly and hit all of the gears? I am very unimpressed with the TKOs for the 2/3 shift and am planning my next Cobra. John |
Before you do anything else, take the shifter boot off and make sure the shifter is not hitting the hole cut into the transmission tunnel. On an ERA they provide a spacer to move the shifter handle over about an inch or so. That makes the fit very tight. If the hole in the transmission tunnel is not cut in exactly the right place, the shifter may be hitting the tunnel causing difficulties.
It might also be a problem with the clutch not fully disengaging. You may need to adjust the clutch using the procedure found in the ERA manual. One last suggestion. As the tunnel on an ERA is screwed down, you need to spread the tunnel slightly. If you don't do that the shift linkage could be rubbing on the inside of the tunnel causing difficult shifting. Chris |
Quote:
I would like to work through this process at some point. https://youtu.be/6UnFDaAdBaM Quote:
Chris - thanks, I'll check that and also dig up the info in the manual. |
My bet is out of adjustment shifter, loose bolt on the 5/R linkage or shifter that has a problem.
If you go under the car, with it in neutral and not running, you can unbolt the shift lever from the 5/R position. It is the one at the rear. You should be able to easily shift into 5/R using an adjustable wrench on the part sticking out of the trans. If that works you know it is the shifter or adjustment. If it won't it is in the trans. Obviously, you may need to rotate the tires just a bit to line up the gear teeth. Once in line it should shift with the wrench. Let me know if my description is unclear. John |
My biggest problem when I had my ERA and that transmission was the 5-4 downshift. VERY easy to grind into reverse if not super careful. As mentioned before the opening in the tunnel is tight.
|
Quote:
Maybe it's the Hurst shifter, maybe the transmission. Either way, not good. Right now, if i do a high rev/fast shift from 2nd to 3rd, the transmission gets into a bad state, maybe in both gears at once? The shifter locks up and I need to keep the clutch in or all kinds of tire squealing starts to happen. The only way to get out of bad state is to bring car to full stop and shift into reverse. Bringing your Cobra to a full stop on a busy road in the middle of heavy traffic is downright embarrassing if not very dangerous. Needless to say, the next time I spent a chunk of money on my Cobra, it will be for a different transmission than the Richmond Gear. |
Quote:
Photos of Long shifter and various shifter handles, as well as installation and adjustment instructions: https://www.gforcetransmissions.com/...peed_Trans.pdf Owners' manual, including service, repair and assembly instructions, as well as some troubleshooting info: http://www.waterlifemagazine.com/Hor...peedManual.pdf |
Try adjusting/bleeding your clutch this worked wonders for me:cool:
|
Had the same issue. Was what "hauss" suggested. Bleed the hydraulic clutch and problem solved.... for a time. Two weeks later same problem so I changed out the m/c and clutch slave and presto! No more problem.
Bleeding the circuit is a whole lot easier than futsing around with linkage. I would try bleeding first. |
For what it’s worth, Richmond Gear transmissions are now built in China. I think I got one of the last ones built in USA. For that reason alone, my next one will be something other than a RG.
|
Richmond web page still says made in USA and Tremec TKO is made in Mexico and Belgium . American made is a strong preference for me.
John |
Quote:
Source: https://www.richmondgear.com/auto-pa...ssion-catalog/ |
Quote:
|
All times are GMT -7. The time now is 11:28 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: