|
How hard is replacing a half shaft on a BDR
I am heading to the strip this weekend with a new set of NT05R drag radials and everyone is telling me I am going to snap the half shaft on my Backdraft, how hard is it to replace if I do break it?
|
half shafts
Well, my nick name for sometime was half shaft. Snapped the first one on GY Eagles at Run N Gun. PS: Three BDR's snapped halfshafts at Run N Gun that year. Second one snapped on the street during a spirited take off, minor bump in the road, tires hopped and SNAP. Getting pretty good a changing them out. Thought about upgrading however what's the next weakest link. May not be as easy to change or as cheap. Start to finish the first time having never done it before about 6 hours by myself. That's tires off the ground, tires back on the ground. Second time 3 hours. These cars are NOT drag race cars. Take it easy on the launch you'll be alright. I ran the Nitto 05's on my car for a short while. Liked them, stickier than the GY's but only last 3,000 miles. I get 6,000 out of the GY's and run Nitto 01's on the track. Good luck, hope this helps.
|
Perfect, sounds like it is not the end of the world if I do break it. Thanks for the reply.
|
Jimbo
You should be made aware of the fact that there is generally a grey/silver Cobra with a IRS that sacrifises and half shaft whenever the Cobras go to Byron |
Here is something else to think about. One of the Cobra's at Run N Gun a couple of years ago not only snapped a half shaft but when he did that he was traveling over 100 MPH on a drag strip and immediately slung him into a cement wall. The half shafts are easy to fix as long as it is just a half shaft. Smooth rolling start before you hammer it to much and you should be ok.
Clois |
Jerry,
Yeah, but that's a Superformance (shoddy workmanship!), it is really titatium in color and you have that old guy Wolfie driving it! Just kidding Mr. Wolfie, by the way, I spoke with your son last night and he was very helpful with telling me how to launch and not snap the halfshaft. He said you did not get the message. |
Good news, nothing broke, now I have to get through May 8th with the WCCC event at Byron.
|
That is a fantastic 60 ft time in one of these cars with your gear ratio....Good driving job.
Justin |
Mistake clois
CLOIS,
RICHARDS YELLOW THAT HAD THE ACCIDENT ON THE DRAG STRIP HAD NO MECHANICAL FAILURE WHAT SO EVER.:CRY: HE JUST GOT ON IT TOO HARD AND LOST IT. I AM SURE THAT RICHARD WILL JUMP IN AND CONFIRM THIS.:p HOPE TO SEE U ALL AT THIS YEARS EVENT. RACING AT THE :DMITTY:D THIS WEEK END.:DIT WOULD BE WONDERFUL TO SEE U THERE.:cool: TAKE CARE |
Stupid Question - I take it back
I did 20 hard runs, the halfshaft works fine - even with Drag Radials!
|
Quote:
Larry |
| All times are GMT -7. The time now is 10:47 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: