mickmate
Mon October 15, 2007 8:02pm
|
Roll bar install CCX
Shows the brackets on Jeffs car where the outside and inside hoop legs and rear brace attach to the frame.
|
|
mickmate
Mon October 15, 2007 8:02pm
|
Roll bar install CCX
Shows the brackets on Jeffs car where the outside and inside hoop legs and rear brace attach to the frame.
|
|
mickmate
Mon October 15, 2007 8:02pm
|
Roll bar install CCX
Shows the brackets on Jeffs car where the outside and inside hoop legs and rear brace attach to the frame.
|
|
imagine2frolic
Thu January 17, 2008 7:24am
Rating: 10
|
Computer room
This is where I wrestle the internet....LOLOLOL
|
|
imagine2frolic
Thu January 17, 2008 8:00am
Rating: 10
|
Imagine's dining table
This is where we mostly eat.
|
|
cobrajam
Mon March 24, 2008 8:18pm
|
ExhaustTip
Need what appears to be a Nelson Exhaust tip 89154A, upc 62712-02109. One was split and I returned to Bob at Midstates. Unfortunately Midstates no longer exists, SV is of no assistance. Anyone know where these can be purchased, please let me know.
|
|
terry251
Sun May 4, 2008 4:46pm
Rating: 10
|
B-17 escape hatch
My Dad and Wife - he was a B-17 co-pilot and that little hatch is where he bailed out over Germany in 1944. He spent the next 18 months as a POW.
|
|
Rick Yeager
Thu October 23, 2008 1:02am
Rating: 10
|
11_Painted_body
Mike and his son, Chris, are standing by the car which is freshly back from his garage where he painted it.
|
|
bermblaster41
Sun November 30, 2008 5:03am
|
DSC00206_Medium_
Position where collector should be
|
|
RJCCOBRA
Fri December 12, 2008 3:03pm
|
Shell Valley build
The first coat of paint has been sprayed in the engine compartment. After it drys, it will be sanded and a second coat applied. I may have to do 3 or 4 coats to get it where I'm satisfied.
|
|
RJCCOBRA
Wed January 21, 2009 3:46pm
|
Shell Valley build
The dash panel has been roughed in and the wiring done behind the panel. We need to scroll the edges and make a cover for the slot where the steering column goes through the dash. Then it's on to covering the dash with vinyl.
|
|
Ron61
Mon January 26, 2009 11:20am
Rating: 10
|
This is where Kilauea dumps its lava into the Pacific.
|
|
Baz
Mon February 23, 2009 8:41pm
|
Extractors_for_nearside_bank_Small_
Just finished welding them up. They have to be painted yet. Now the fun starts making the offside extractors as this is where the steering column is.
|
|
Ken Williams
Tue March 3, 2009 5:18pm
|
At Operation Comfort
Some of the Texas Cobra Club members went to a Ranch south of San Antonio where disabled Vets from Brooks Army Hospital are being rehabilitated. We gave rides and donated some tools
|
|
kitcarbp
Fri March 6, 2009 7:29am
Rating: 9
|
Ford_Raditor_Heat_Rejection_Chart- Street Rod Example
This chart compares the heat rejection rate (cooling capacity) of three different types of radiators tested on an old Ford Street Rod. Coolant flow rate is held constant at 7 gpm (typical flow at idle perhaps, not sure where its being measured ???). It graphs the heat rejection for each radiator versus air flow through the radiator core. It is comparing 3 diff rad designs/materials at different CFMs through the core. The more air flow you have for a given coolant flow rate (7 gpm in this example) , the higher the heat rejection, basically linear in this example. The author of this graph is most likely selling the high efficiency radiator showing the improvement over the other two designs. To sum it up, the radiator at the top of the chart appears to be the most efficient at a low coolant flow rate (7 gal/min) over all air flows tested. Ya see how important rad core/tank design is? I learned something here.
|
|
