About Me
- About olddog
- Zip Code
- 43071
- City
- St. Louisville
- State
- Oh
- Interests
- Hunting
- Country
- usa
- Cobra Make, Engine
- A&C 67 427 cobra SB
- Engine type and displacement
- 5.0 bored & stroked
- Tranny type
- TK 600 5 speed
Visitor Messages
Showing Visitor Messages 1 to 1 of 1
-
03-31-2013 02:51 PM - permalinkDirty HarryHey Rick,
Last fall, I did some clutch work. I took the car out and really beat it up to make sure the clutch was going to work out well. When I got home, I noticed a mark on the left side pipe where the engine had torqued over, allowing the header to contact the body.
Sure enough, the tab that's welded to the frame where the motor mount bolts up had broken. The weld failed. Not Shell Valley's fault. When I installed the engine, I had to cut that tab off and re-weld it. It was my weld that failed, not theirs. No way to get to it without pulling the motor, so I'm doing some cleanup under the hood and putting on new valve seals while the engine is out.
I'm registered for LCS. That ought to get me going on re-assembly. See you there.
Mike
Likes Received
319 Likes
-
jolsen42 liked post by olddog On thread : OMG!!! What The??Great hoax with a stuffed animal. No life in the eyes. Hair out of place. Tail sticking up and straight. Teeth too long. BB Chevy. The Rat Engine. Swallowed by a Cobra.Liked On: 09-24-2023, 08:47 AM
Posted On: 03-17-2018, 07:53 AMHarpoon PV2 liked post by olddog On thread : OMG!!! What The??Great hoax with a stuffed animal. No life in the eyes. Hair out of place. Tail sticking up and straight. Teeth too long. BB Chevy. The Rat Engine. Swallowed by a Cobra.Liked On: 09-23-2023, 09:15 PM
Posted On: 03-17-2018, 07:53 AMvntgspd liked post by olddog On thread : Hoist cable shreaded!I work in a factory that uses cable hoists to remove (1500 lb +/-) rolls of plastic film from a winder. I can count 21 hoists in my head, two of which are 5 ton hoists that reach the first floor and...Liked On: 02-25-2022, 09:23 AM
Posted On: 11-08-2019, 05:40 AMCompFi liked post by olddog On thread : Hoist cable shreaded!I work in a factory that uses cable hoists to remove (1500 lb +/-) rolls of plastic film from a winder. I can count 21 hoists in my head, two of which are 5 ton hoists that reach the first floor and...Liked On: 02-24-2022, 07:54 AM
Posted On: 11-08-2019, 05:40 AMTom Wells liked post by olddog On thread : I'm finally healthy againI spent most of last year in the hospital. I had a liver transplant in April and a kidney transplant in December of last year. I had a lot of difficulties with the liver transplant, but the kidney...Liked On: 02-09-2022, 01:59 PM
Posted On: 02-08-2022, 05:20 PMLinks monetized by VigLinkBob K liked post by olddog On thread : I'm finally healthy againI spent most of last year in the hospital. I had a liver transplant in April and a kidney transplant in December of last year. I had a lot of difficulties with the liver transplant, but the kidney...Liked On: 02-08-2022, 10:16 PM
Posted On: 02-08-2022, 05:20 PM440.mustang liked post by olddog On thread : Small block Chevy in a cobra?If it is your car you can do what you want, but don't expect praise for things other's do not appreciate. I have owned plenty of small bock Chevy cars in my puppy days. I have personally built a...Liked On: 10-02-2021, 09:31 AM
Posted On: 05-13-2020, 03:33 PMDwight liked post by olddog On thread : Small block Chevy in a cobra?If it is your car you can do what you want, but don't expect praise for things other's do not appreciate. I have owned plenty of small bock Chevy cars in my puppy days. I have personally built a...Liked On: 09-08-2021, 07:48 PM
Posted On: 05-13-2020, 03:33 PMeschaider liked post by olddog On thread : 427w back from rebuild with dyno resultsPatrick, The reason to correct for horse power is that if you dyno an engine along the coast, sea level, and dyno that same engine in Bolder Colorado, the uncorrected results is extremely...Liked On: 02-04-2021, 01:33 PM
Posted On: 02-04-2021, 10:51 AMtkb289 liked post by olddog On thread : Ok now that you have had your Cobra what would you changeIt sounds to me that most comments are about the owners priorities have changed. The newbies first posts are what should I buy or which replica is best. We always reply with what do you want to...Liked On: 01-09-2021, 10:20 AM
Posted On: 01-05-2021, 08:20 AM1985 CCX liked post by olddog On thread : cable to linkage conversion?I should clarify what I said. There is not a problem with linkage that both ends connect on the engine assembly and nothing is connected off of the engine. The problem is when the linkage is...Liked On: 12-31-2020, 06:41 AM
Posted On: 12-23-2020, 01:31 PMERA 626 liked post by olddog On thread : cable to linkage conversion?All though the ERA linkage is period correct, you should know that was very unsafe technology. I woke up one morning and hopped in my 66 Cyclone, started it, and dropped it into reverse. When I...Liked On: 12-24-2020, 12:40 PM
Posted On: 12-23-2020, 01:01 PMhauss liked post by olddog On thread : New Tremec transmissionA member for 8 years and only 74 posts suggests a quiet fellow. With the plague, people dying, and political crap happening, and not knowing any personal circumstances, I vote to drop it and let...Liked On: 12-09-2020, 11:20 AM
Posted On: 12-09-2020, 10:58 AMAlfa02 liked post by olddog On thread : new cobra comingSafety! Safety! Safety! Take some time driving and sorting out the car. Stay off the main routes and take it slow for a while. A loose bolt in the wrong spot is very bad at highway speeds. Put...Liked On: 11-22-2020, 03:21 AM
Posted On: 11-21-2020, 08:11 PM
All times are GMT -7. The time now is 02:32 PM.






Likes Received