Club Cobra - View Profile: LoBelly

LoBelly
Senior Club Cobra Member

Last Activity: 12-13-2023 12:52 AM

About Me

About LoBelly

City

Melbourne

State

VIC

Country

Australia

Cobra Make, Engine

RMC, carb 347 TopLoader and Jag running gear ~ so old school I time it with an hour-glass :D

Statistics

Total Posts

Total Posts: 1,293
Posts Per Day: 0.18
Find all posts by LoBelly
Find all threads started by LoBelly

General Information

Last Activity: 12-13-2023 12:52 AM
Join Date: 02-22-2006

Friends

Showing Friends 1 to 2 of 2

Excaliber

Senior Club Cobra Member
sickntwisted

CC Member

Likes Given

563 Likes

LoBelly liked post by stephen low On thread : Engine oil leak

Thanks all guys. Can also lean on a good mate and fellow sailor for advice who is a mobile mechanic. Have ended up with the right Permatex gasket set and after a clean up, I test fitted the...
Liked On: 02-23-2021, 01:51 PM
Posted On: 02-23-2021, 03:45 AM
LoBelly liked post by Gaz64 On thread : Engine oil leak

I see a split cork valley seal between the bottom LHS of the manifold and the top of the block. I don't use cork at all. Run a bead of silicon (I like UltraGrey) of a little higher than the...
Liked On: 02-16-2021, 12:40 AM
Posted On: 02-15-2021, 05:58 PM
LoBelly liked post by xb-60 On thread : AP2289 Build log 'stage 2'

These came in from the UK on Christmas Eve....:D 35570 ....making mounting brackets for them now. Cheers! Stay safe, friends Glen
Liked On: 01-05-2021, 05:19 PM
Posted On: 01-05-2021, 03:12 AM
LoBelly liked post by patrickt On thread : FE vs Roush vs Blueprint

I will say that FE powered Cobras, as a general rule, are pretty easy to work on as compared to new cars. My auto shop text books from my classes in the 70's are actually quite timely for a lot of...
Liked On: 12-21-2020, 10:51 PM
Posted On: 12-20-2020, 11:28 AM
LoBelly liked post by ssv ute On thread : My build at the moment

Hi Guys, Not sure if anyone still out there, a few pics of where i'm at with my build.
Liked On: 11-27-2020, 01:39 AM
Posted On: 10-15-2019, 04:33 AM
LoBelly liked post by Luce On thread : Speedmaster 8 stack EFI

I have one on a 383 SBC, I got the model with no plenum then fabricated 2 separate plenums, One for the MAP and another for a ford idle air motor, Then I swapped the L and R throttle bodies to hide...
Liked On: 11-09-2020, 05:14 AM
Posted On: 11-02-2020, 06:06 PM
LoBelly liked post by steelcomp On thread : Pump gas 390 build, iron heads, 520hp

It's been a while since I've posted here in Club Cobra but I thought I'd share a recent FE build I did. Not for a Cobra but for my 67 Fairlane. Nothing really exotic, no thin rings, no trick heads,...
Liked On: 11-09-2020, 05:10 AM
Posted On: 11-08-2020, 12:33 PM
LoBelly liked post by xb-60 On thread : AP2289 Build log 'stage 2'

One job that didn't take too long to complete in the last couple of days is a tow lug for the front end. It's 50mm x 6mm section mild steel, ø25mm hole, attached to the chassis with a couple of...
Liked On: 11-09-2020, 05:07 AM
Posted On: 11-02-2020, 02:44 AM
LoBelly liked post by 1795 On thread : Superformance MKII, Riverside Racer 289 FIA vintage race car

Well, it's been a difficult race season, with the majority of races getting cancelled. I washable to get one last race weekend in at Watkins Glen this past weekend. It was with the Vintage Racers...
Liked On: 10-26-2020, 05:59 AM
Posted On: 10-19-2020, 08:19 AM
LoBelly liked post by Tom Wells On thread : Shims

Geoff, Whoops! Tom
Liked On: 09-29-2020, 04:40 PM
Posted On: 09-29-2020, 06:43 AM
LoBelly liked post by 767Jockey On thread : After 13 years, it's alive.

After 13 long years, the never say die car is alive finally. I am going to try to attach a video here, I'm not sure if that's possible. There's still lot's to do ahead, but it runs and drives. I have...
Liked On: 07-12-2020, 12:42 AM
Posted On: 07-09-2020, 07:28 PM
LoBelly liked post by 767Jockey On thread : Some details on my 520 cu. in. FE engine

Some of you commented on my other thread and in comments sent to me asked about the details on my engine. Here are some of the specs on it: BBM cast iron FE block BBM cylinder heads, as cast...
Liked On: 07-12-2020, 12:41 AM
Posted On: 07-11-2020, 05:20 PM
LoBelly liked post by Ivygreen65 On thread : My Street 289 build

I’m pretty lucky - a few years back, she let me have 2 days to get the Mustang’s C4 rebuilt before I got sent to a cold a garage. I got finished in a day. ...
Liked On: 06-01-2020, 05:01 AM
Posted On: 04-14-2020, 04:19 PM
LoBelly liked post by AC Ventura On thread : Avon cr6zz tires ?

Avon’s the default tyre for most of us engaged in any form of motorsport, here in the U.K. Its a quality, strictly controlled manufacture tyre that is relied upon and the ‘control tyre’ in many...
Liked On: 06-01-2020, 04:51 AM
Posted On: 05-31-2018, 03:41 PM
LoBelly liked post by 1795 On thread : Superformance MKII, Riverside Racer 289 FIA vintage race car

Glen, The Cobra is a she so as to maintain my masculinity, because I love her...and she will kill you in a heartbeat, just like any good woman :LOL:
Liked On: 05-25-2020, 07:11 AM
Posted On: 05-19-2020, 04:31 AM

Page 1 of 38

Last »

About Me

Statistics

Friends

Likes Given

Mini Statistics

Friends

Recent Visitors

	sickntwisted CC Member