Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Search Forums
Reload this Page Search Results
Portal Register FAQ Community For Sale Gallery Calendar Today's Posts

MMG Superformance
Nevada Classics
Main Menu
Portal
Forums

Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
April 2026
S M T W T F S
      1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30    
Showing results 1 to 11 of 11
Search took 0.03 seconds. Search: Posts Made By: CALHOON
Forum: Transmission Talk 08-06-2004, 09:04 AM
Replies: 18
Views: 2,043
Posted By CALHOON
I have seen the sline protectors on many autos...

I have seen the sline protectors on many autos and manuals. They are simply plastic caps that fit over the output spline.I think you are confusing the spline protector with the splined seal. Tremec...
Forum: Transmission Talk 08-06-2004, 07:51 AM
Replies: 18
Views: 2,043
Posted By CALHOON
I think there may be a problem with how much...

I think there may be a problem with how much would / should be on such a sheet. Do yo tell a guy he has to balance a shaft after its' modified? Do you tell them to preserve the angle? How about the...
Forum: Transmission Talk 08-06-2004, 04:33 AM
Replies: 18
Views: 2,043
Posted By CALHOON
It is truely a matter of care and caution when...

It is truely a matter of care and caution when installing a trans that really saves damage to the sel. You have proven that . There is an element that use no caution nor care and that is why the...
Forum: Transmission Talk 08-05-2004, 08:23 AM
Replies: 18
Views: 2,043
Posted By CALHOON
I would think that if it were a nick/ cut to the...

I would think that if it were a nick/ cut to the seal lip, it would manifest as a seeping / slight leak that would leave several drips from time to time. If the garter spring is dislodged it would be...
Forum: Transmission Talk 08-05-2004, 08:12 AM
Replies: 12
Views: 1,376
Posted By CALHOON
I prefer the defined( some call them notchy)...

I prefer the defined( some call them notchy) shifts Not clunky but crisp. I should look at the latest Honda stuff ( I have not). I have not listed my car here because it is not a Cobra. I have a...
Forum: Transmission Talk 08-05-2004, 08:01 AM
Replies: 18
Views: 2,043
Posted By CALHOON
Your experience( damage to the seal) is exactly...

Your experience( damage to the seal) is exactly why it is intended to be pushed in. Yes it may take more grunt than you would expect installing the yoke, but it is very effective.
Forum: Transmission Talk 08-05-2004, 07:56 AM
Replies: 18
Views: 2,043
Posted By CALHOON
We may be talking of two different parts. There...

We may be talking of two different parts. There is a molded plastic spline protector the covers the out put spline. There is also what is called the donut. It seals the spline to the lip seal. It...
Forum: Transmission Talk 08-05-2004, 06:46 AM
Replies: 12
Views: 1,376
Posted By CALHOON
I think if you did not like the feel of the T56 ,...

I think if you did not like the feel of the T56 , you will not like the Tremec/ TKO either. You could get a shorter throw shifter(aftermarket) but it would just increase the feel / shift load. I have...
Forum: Transmission Talk 08-05-2004, 06:28 AM
Replies: 18
Views: 2,043
Posted By CALHOON
It is designed to be pushed in with the drive...

It is designed to be pushed in with the drive shaft and be there forever. The reason you would not remove it is that poking around the seal lip with any kind of tool that may damage it is not a...
Forum: Transmission Talk 08-05-2004, 05:09 AM
Replies: 9
Views: 1,426
Posted By CALHOON
I think you touched on a mod here. Its an old...

I think you touched on a mod here. Its an old trick to remove some of the clutch teeth from the locking sustem. Generally a bad Idea to take them off the gear. Better to take them off the synchro...
Forum: Transmission Talk 08-05-2004, 04:49 AM
Replies: 9
Views: 1,257
Posted By CALHOON
If it isn't jumping out of the gear it's in, It...

If it isn't jumping out of the gear it's in, It may be the reverse idler gear attempting to slide into mesh. This could happen if the spring that holds it out of mesh were not fastened at the front...
Showing results 1 to 11 of 11

 

All times are GMT -7. The time now is 08:07 PM.

Contact Us - Club Cobra Home - Archive - Top

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink