Club Cobra Gas - N Exhaust  


Keith Craft Racing
Nevada Classics
Keith Craft Racing
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
Keith Craft Racing
Keith Craft Racing
Keith Craft Racing
April 2024
S M T W T F S
  1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30        
  Home · Search · Member List · Register  

Home » Cobra Stuff for Sale » Cobra/Daytona/GT40's for Sale (private party sales only) « Previous Ad  · Next Ad »

IR EFI 9.2 deck Windsor C302B Head Ads from this Seller · Contact Seller
For Sale By Views Date Posted
kcoffield 2299 Wed June 3, 2015
Asking Price Condition
$4,500.00 Excellent



Description: This is a custom IR EFI induction system for 9.2” deck Windsor style block with high port C302B heads. It is low profile and will comfortably fit under the hood of most passenger cars with filter assemblies. Years ago I made a few dozen such systems and the tooling to cast these high port intakes. Recently, one of the intakes found its way back home to me and I completed the system below. This particular intake has an integral water neck. It also has the Cleveland rear valley land cast on the underside so would seal on a Cleveland block and could be trimmed to accommodate.

The intake runners are step-over CNC ball end milled to match the 50mm throttle body openings and transition to the C302B Port size (1 5/16”wide x 2 1/8” tall) and position. Though the ports are presently matched to early C3/C302B Ford high port heads, there is enough stock in the lower runner walls to be ported to A3 head width (1 Ύ” wide) and accordingly can accommodate B3 heads as well.

This system is configured as follows:

• Weber IDA mounting pattern 50mm throttle bodies with o-ring seal to intake flange and velocity stacks.
• Velocity stacks 1.5” tall.
• Filter assemblies, anodized aluminum ball end mill engraved as shown, natural aluminum in color, with 2”tall washable K&N filters. These filters remove as an assembly with two wing nuts while retaining the filter element.
• Fuel rails and mounts. These take -6 straight thread O-ring boss AN fittings on each end.
• Linkage wheel mounted in sealed ball bearings and Teflon lined rod ends on link arms. Also uses Kinsler spring screw connectors to prevent binding due to thermal growth and angular misalignment. This linkage produces nice progressive action for good off idle and low speed resolution. Each bank of TBs counter-rotate with the low side of the butterfly on each bank on the valley side of the intake to promote symmetric flow in each bank. Each bank of TBs has an idle and full open adjustable stop.
• Vacuum plenum and lines to each runner are included with a -6AN port on the plenum so you can run a line to a MAP sensor for typical speed density ECU control scheme.
• Ships in the plastic tote as shown.

Needed to complete installation:

• Add fuel injectors and sensors. Borla offers a D-shaft drive TPS (2900-3040) that bolts up to the end of the front passenger side TB. Note the PN specifies the butterfly opening CCW rotation for voltage increase to accommodate this induction system as configured.
• Adapt an accelerator cable and return spring scheme to interface with linkage wheel on the intake.
• Add fittings for fuel delivery and return lines.
• EFI compatible fuel delivery system and preferred ECU.

$4500 delivered UPS Ground in continental US.

Best,
Kelly

Please send inquiries to kcoffield "at" mchsi.com





Keywords: stack induction IDA weber IR EFI C302B High Port


Powered by: PhotoPost Classifieds PHP vB3 Enhanced
Copyright 2006 All Enthusiast, Inc.


All times are GMT -7. The time now is 12:59 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink