|
Scissor Lift
I am putting a scissor lift in a new garage building. I had the foundation poured to accommodate a BendPak SP-7X in ground for a level floor when it is down. But the wells can be easily modified at this state for anything else that might make more sense. I want the floor clear of posts, so I'm set on the scissor style in ground for my use.
Any suggestions/opinions of something that might be better than the BendPak? Thanks, |
I'll be watching for the answers on this one. I'm looking for a sissor lift as well but have concerns on how stable they are from side to side or if the twist. If someone has one, please address this stability issue as well. Thanks
|
Wayne: That's what I bought years ago (2004), for a Porsche I had. Worked great for that, as there's nothing in the middle of the Porsche chassis. Pain in the butt for a front engine rear drive tranny in the middle car (Cobra), but better than jack stands. Had to build wooden ramps to drive Porsche/Cobra over the hoist because their listed height for the collapsed lift did not take into account the safety latch which sticks up another inch or two. Recessed into the floor should take care of that.
If I had the ceiling height I'd prefer a two post (they have short ones now) But if you're limited by ceiling you'll be happy with the scissor type. My Bend pac has been trouble free so far ! Ted |
Greg: stability is not a problem. weight limit on mine is 6000 lbs, so very stable at 2000-3000 lbs.
|
Wayne,
I've had a Bend-Pak for about 10 years now and it has been trouble-free. I like that I can move it around the garage to accommodate either 2 or 3 cars parked there. You will lose that flexibility if you set it in concrete, so to speak. On the other hand, I have to use 2X12 planks to drive the cars up on in order to clear the safety latch, as Ted has mentioned above. The Ferrari requires one plank on each side; the Cobra needs two each side. The recently sold Alfa Romeo didn't need the planks at all. Imagine a couple of 2X12s linked by a 2X4 to make an "H" and with small coaster wheels attached to the tops of the 2 by 12s. That's what I've jury-rigged to move the planks if I want to move the lift, plus the 2X4 keeps the 2X12s at a set distance from one another. Cheers, Mark |
I installed the BandPak P-6FB. It is recessed 3/4" to make way for a 3/4" ply cover for a flat shop floor. The most important criteria was being able to get between the stands for motor and transmission service.
The other lift that looks interesting is the new BendPak portable lift. No pit, completely portable, a good choice for occasional use. The pit has turned out to be a 'magnet' for tools, washers and small nuts. |
I don't have anything as extraordinary as a hydraulic or motorized lift, however I do have a Kwiklift which I love because I have unobstructed access to the full underside which has come in very handy frequently. My point isn't to get a Kwiklift, but rather to point out you will not regret ever having access to the entire underbelly of your car.
I was contemplating the Bendpak scissor lift and am very glad I didn't get it for that reason. The regret, I do have (and that's somewhat harsh), is the inability to remove wheels, in which case, I'd raise the car on jack posts when off of the Kwiklift. What do I prefer better if I can't have both the access to wheels and access to the underside? Access to the underside. There were other drivers for the Kwiklift such as I move frequently and can take the Kwiklift with me or store it while living overseas, however its a personal choice and just my view. Good luck and keep us posted. |
I have the SP 7X. It's solid. I thought about putting it level with the floor as well. But it has been fine as-is. Flush would be cool.
You will of course, lose some clearance height by putting it in the floor. Note that it does drift back some as it goes up. So the car will end up going backwards a few inches as you lift it. This may be crucial if you are going to set the lift flush. You won't be able to make adjustments fore/aft if you don't get it right the first time. The lifts end up being nice tool shelves when working on the car. |
The regret, I do have (and that's somewhat harsh), is the inability to remove wheels, in which case, I'd raise the car on jack posts when off of the Kwiklift.
Just a question but didn't you get a bridge with your Kwiklift? I got one along with jacks and I have no problem at all with removing wheels when the car is on the lifts. The bridge is heavy but very stable. Ron Quote:
|
I have a scissor lift I will probably recess into the floor at some point. For the time being it needs planks to wheel them over. I think having access to everything except the underneath of the tranny is the best access to your car for working on it above and below. The frame rails in the middle of most Cobra frames need some long reach arms on a post lift which tends to make them less stable in my opinion. I'd say go for it on the scissor style.
|
Widows Son, I don't follow what you are saying. The Bend Pak SP 7X has full access to the underside. I can get to everything with nothing obstructed. Check out the video. http://www.bendpak.com/car-lifts/spe...fts/sp-7x.aspx
|
Quote:
|
Sidepipe clearance
Hi,
Learning a lot here. Want to get a mid-rise to do light maintenance and detailing of my BDR and other vehicles. Is there an issue with sidepipe clearance and distance from wheel to wheel span?...thanks Bill |
I build my car on a Table Lift, with the table removed. I fabricated a frame which accommodates the ladder frame of the Cobra 289 or 427.
I'm looking for a lift at home. Same type of table lift. The advantage is, when you lower the lift it is just a metal platform even with the garage floor. Besides that you have an adjustable heavy duty table middle in the garage - for all kinds of work. http://photos.imageevent.com/germanp...m_DSC06697.jpg Jack from the 911 forum did a fantastic job, my plan is to do the same (minus the tile hehe)..... http://img135.imageshack.us/img135/1091/roughedin.jpg http://img189.imageshack.us/img189/3...ownrightlr.jpg http://img717.imageshack.us/img717/9...ruprightlr.jpg FYI: For Porsche owners is the lift table easily justified: An oil change is at the dealer around $500 - DIY about $120.... |
|
I guess I got lucky. When I built my house the garage ceiling ended up over 12 feet.
Here is a photo of my Porsche on the lift, soon to be replaced by a Superformance Cobra. http://www.smugmug.com/photos/i-Vzvs...-Vzvszqh-L.jpg I just ordered a rolling jack. http://www.smugmug.com/photos/i-Vw9V...-Vw9VcSR-L.jpg Should be pretty handy but I'll wait until the jack arrives and I get to play with it. I park under the lift all winter. |
Very Inexpensive Alternative
OK, this isn’t even in the same category as the Kwiklift or BendPak, but a relatively inexpensive alternative for getting the Cobra off the ground.
http://www.harborfreight.com/media/c...mage_25291.jpg Steel Floor Jack Cross Beam Of course a floor jack and jack stands will be needed, but most folks will already have these. It seems like this would provide a quick and easy way to get the front and rear, or an individual side, off of the ground to get jack stands under it. It has a two ton capacity (it's just shown on a four ton jack), so half a Cobra should be no problem. Some pluses and minuses (ie., jack stand bases take up more space underneath, but could be moved to accommodate; limits on just how high you can go), but if you already have a jack and jack stands, and are limited on space, this is a very small additional expenditure. If skeptical of HF, they are also available from Northern Tool, Summit Racing, and even Amazon. I don’t have one, so I can’t provide any personal experience, but most of the reviews seem to be favorable. I am strongly considering purchasing one for working on my passenger vehicles if nothing else. Like I say, just a quick and inexpensive alternative. |
Nussbaum is the best unit I've found.....been using it for many years and is great....a bit on the expensive side but forth every dime.......we even put 2x4 tubing across the plates to lift mini vans.....
Now they have one that goes up to 9000#lbs... JUMBO 7000 | Double Scissor Lift | Nussbaum Automotive Solutions Morris |
Quote:
http://i1294.photobucket.com/albums/...psd75f9c17.jpg |
| All times are GMT -7. The time now is 01:03 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: