Club Cobra Keith Craft Racing  

Go Back   Club Cobra > Cobra Talk Areas > ALL COBRA TALK

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
Keith Craft Racing
Keith Craft Racing
Keith Craft Racing
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree9Likes

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 09-13-2018, 08:14 PM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default Spark plugs are hitting the pistons. Help!

Running very rough. Pulled the plugs and the electrode is pushed against the other electrode. Virtually no gap. What’s happening?
Reply With Quote
  #2 (permalink)  
Old 09-13-2018, 08:40 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

Bill, From an earlier post you listed your build being a 331SBF with Trick Flow 205cc heads.

From the Trick Flow catalog they list an Autolite 3924 as the plug if that helps.
https://static.trickflow.com/pdf/catalog_2018.pdf (page 41)
Reply With Quote
  #3 (permalink)  
Old 09-13-2018, 08:49 PM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

.thanks. Upon closer analysis, it appears the exhaust valve is kissing the spark plug, flattening the electrode
Reply With Quote
  #4 (permalink)  
Old 09-13-2018, 09:08 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

That is strange. I would think not possible that they'd design their highest flowing heads, which folks would put high lift cams in and then place the spark plug in the path of the exhaust valve travel?

It could be detonation.

I'd make sure you have fresh gas, plug gaps @ .035". Whats your Base and full advance set at?

Last edited by spdbrake; 09-13-2018 at 09:11 PM..
Reply With Quote
  #5 (permalink)  
Old 09-13-2018, 09:18 PM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

Would detonation push the electrode flat? Seems weird. Timing hasn’t been set yet. Haven’t noticed any detonation issues.

I plan to call trick flow tomorrow
Reply With Quote
  #6 (permalink)  
Old 09-13-2018, 09:23 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

Smashed electrode http://4.bp.blogspot.com/-c0RcgGHOXC...detonation.jpg

Trickflow 205cc heads combustion camber
https://cdn2.bigcommerce.com/server5...0.1280.JPG?c=2
Ron61 and Bill D like this.

Last edited by spdbrake; 09-13-2018 at 09:29 PM..
Reply With Quote
  #7 (permalink)  
Old 09-13-2018, 09:29 PM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

Thanks a bunch. I believe the timing is too far advanced. I’ll reset it tomorrow.
Reply With Quote
  #8 (permalink)  
Old 09-14-2018, 04:27 AM
undy's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2005
Location: Virginia Beach, Va & Port Charlotte, Fl.,
Posts: 2,280
Not Ranked     
Default

Ignition timing isn't going to affect PTV contact. The engine need to be torn down, at least head removed. "Possibly" a thicker head gasket will fix the problem. It sure sounds like some mismatched parts (pistone/rods).
__________________
Too many toys?? never!
Reply With Quote
  #9 (permalink)  
Old 09-14-2018, 04:35 AM
Ron61's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Shasta Lake, CA
Cobra Make, Engine:
Posts: 26,552
Not Ranked     
Default

Possibly if the exhaust lobe on the cam is higher than the intake and this doesn't happen at lower RPM then you may need a stronger valve spring. I did see this happen on a car that some guys were building to drag race. It ran OK at idle and lower RPM but when they started to open it up the valves hit the pistons and completely wrecked their motor. They went to the cam manufacturer and they told them the valve springs they used were way to light and they needed much stronger ones for that cam.

And as Undy said, there could be some mismatched parts. Anyway I hope the fix turns out to be a simple and easy one.

Ron
__________________
Ron 61
Ronnie Widener


View my Miscellaneous Gallery
Reply With Quote
  #10 (permalink)  
Old 09-14-2018, 06:59 AM
Danr55's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2007
Location: Mesa, AZ
Cobra Make, Engine: Contemporary Classic, 428 FE CCX 3069
Posts: 7,500
Not Ranked     
Default

It's been awhile since I've torn down a small block motor, but I don't believe that the valves can hit the spark plug. If anything is hitting the spark plug it would seem that it would have to be the head of the piston. That tells me that possibly the spark plug is being used is wrong was too deep ahead or the engine was built wrong. What am I missing?
__________________


Dan in Arizona
CCX3209


"It's a great car and I love it, but it doesn't do 'SLOW' very well."
Reply With Quote
  #11 (permalink)  
Old 09-14-2018, 08:11 AM
LMH's Avatar
LMH LMH is offline
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2005
Location: Tucson, AZ
Cobra Make, Engine:
Posts: 5,389
Not Ranked     
Default

Valves hitting the plug sounds impossible. The plug would have to be WAY down inside the chamber. Something else is going on there.
Larry
__________________
Alba gu bràth
Reply With Quote
  #12 (permalink)  
Old 09-14-2018, 08:33 AM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

After analyzing the situation more, I’ve come to the belief the piston domes are kissing the plug electrodes.

I just got off the phone with the tech support guy at NGK spark plugs. Told him my situation and they were able to find a shorter spark plug with a better heat range for my compression. Going to get those today install them tonight and crank it over without the coil wire attached. Then I’ll pull a couple plugs and see if that fixes the problem.
Reply With Quote
  #13 (permalink)  
Old 09-14-2018, 08:51 AM
Karl Bebout's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2001
Location: Mesa, AZ
Cobra Make, Engine: ERA #2119 289FIA
Posts: 5,380
Not Ranked     
Default

Bill, had you been using the 3924 or its equivalent?

If so, hope the shorter plug does the trick.

Mighty strange, if the proper parts have been used.
__________________
Karlos
"In the Land of the Pigs, The Butcher is King"
Reply With Quote
  #14 (permalink)  
Old 09-14-2018, 10:32 AM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

I think my problem stems from using a domed piston with zero deck height, allowing the dome to move further up into the combustion chamber. The shorter plug should be the fix. I sure hope so
Reply With Quote
  #15 (permalink)  
Old 09-14-2018, 11:10 AM
CC Member / Sponsor
Visit my Photo Gallery

 
Join Date: Jan 2002
Location: Provo, UT
Cobra Make, Engine: Daytona Coupe
Posts: 1,356
Not Ranked     
Default

If you are talking about the threaded portion of the spark plug, you just can't use a shorter plug. The threaded portion of the plug length has to match the threaded portion of the spark plug hole in the head. If the plug is too short then you will have exposed threads from the spark plug hole. If the plugs are too long then you will have the threads from the spark plug exposed. Exposed threads in the combustion chamber will cause pre-ignition. That being said you might be able to index your spark plugs so they clear. You also might be able to find spark plugs with shorter electrodes. Or something maybe a surface gap plug like this: https://www.summitracing.com/parts/n...BoCHSgQAvD_BwE
Gaz64 likes this.
__________________
Evolve Lubricants
https://evolvelube.com/
Cubic Performance
Reply With Quote
  #16 (permalink)  
Old 09-14-2018, 12:12 PM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

Thanks Tom
The new spark plug still has the .750 threaded area but the tip is not projected. According to NGK tech this reduces the length .100 which hopefully does the job
Tom Kirkham likes this.
Reply With Quote
  #17 (permalink)  
Old 09-14-2018, 12:21 PM
Danr55's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2007
Location: Mesa, AZ
Cobra Make, Engine: Contemporary Classic, 428 FE CCX 3069
Posts: 7,500
Not Ranked     
Default

If that fixes your problem, would it make sense to pull the heads and check the pistons for damaged crowns?
__________________


Dan in Arizona
CCX3209


"It's a great car and I love it, but it doesn't do 'SLOW' very well."
Reply With Quote
  #18 (permalink)  
Old 09-14-2018, 12:24 PM
Bill D's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2006
Location: Redding, CA
Cobra Make, Engine: FFR chassis and suspension, Mr. Bruce 289 FIA body
Posts: 1,066
Not Ranked     
Default

Dan, I just don’t want to do that. I really don’t.

Here is a picture of the new (left) and the old (right) plugs
Gaz64 likes this.
Reply With Quote
  #19 (permalink)  
Old 09-14-2018, 12:28 PM
cycleguy55's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2014
Location: White City, SK
Cobra Make, Engine: West Coast, 460 CID
Posts: 2,844
Not Ranked     
Default

Quote:
Originally Posted by Bill D View Post
Thanks Tom
The new spark plug still has the .750 threaded area but the tip is not projected. According to NGK tech this reduces the length .100 which hopefully does the job

0.100 shorter should be plenty - if you need more than 1/2 that your current plugs would show a lot more damage than just closed electrodes.
__________________
Brian
Reply With Quote
  #20 (permalink)  
Old 09-14-2018, 12:33 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2015
Posts: 1,442
Not Ranked     
Default

A cheap endoscope will allow you inspect the piston tops and camber areas.
You may need to use the mirror attachment (please use a good quality tape as insurance it does not pop off inside the camber)
I use mine quite a bit to inspect areas, retrieve part numbers off parts, etc...

https://www.amazon.com/Endoscope-Wat...ndoscope&psc=1
Bill D and DanEC like this.

Last edited by spdbrake; 09-14-2018 at 12:49 PM..
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 01:14 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink