Knock Offs
Any advice for treating the spinners on knock offs? Anti-seize on the base of the spinner? other? nothing?
|
Quote:
|
I have used Spinner-Eaze from Cobra Valley for well over a decade. Cobra Valley's Chemicals - Spinner Eaze Anti-Seize It is the easiest stuff to put on, easy to wipe off the excess, and it works very well. Better than the sticky paste, IMO.
|
Patrickt, I'd heard about Cobra Valley's Spinner -Eaze. Have you found a solvent that will cut the product for cleaning?
|
I've been using Spinner-Eaze from Cobra Valley for 6 years now and I won't use anything else. It wipes up with a rag I don't use any solvents.
|
Quote:
|
Put some on the PIN mating surfaces as well. Best to clean and retreat annually.
|
After a decade or so, I think they almost become like the old Oilite pilot bushings that you would soak overnight in a mayonnaise jar full of engine oil. I could probably get by now with just the "ooze" from the hub threads.:D
|
I use light coat of Anti-seize and then be sure to pull wheels off annually.
Seems the wheels that are on for longer periods of time have issues. |
Cleaning old paste out of the hub threads is no fun.
That Cobra Valley stuff seems to do the trick just fine. |
Y'all talked me into it. I'd just recently cleaned up my spinners and adapters and re-never-seized them. Wire brush, paint thinner, and lots of paper towels. Sorta nasty job. Just ordered some Spinner Eaze and will go through the cleaning thing again and then give the Eaze a shot.
|
Karl
Use sparingly. You do not need much |
Thanks Dusty, I will.
Just like BrillCream: A Little Dab'll Do Ya. |
I use the Cobra Valley liquid Never Seize also. Best stuff I have ever seen.
|
Update: Seems I can never do anything the easy way...oh well.
That 911 Spinner Tool from Cobra Valley is a nice piece but it doesn't work on my ERA FIA Trigo Rims. The stud doesn't stick out far enough to grab the rim properly. Spinner-Eaze from Cobra Valley went on nice and cleanly. The last person that put my spinners on really knocked them on (too) tightly. After talking to several people, I thought I would share their combined wisdom; it has work for me: 1. 6 lb lead hammer; 2. Jack up the target wheel; brace jack on control arm to minimize "give"; 3. Rotate wheel after 2-3 wacks on each ear to next ear; 4. Make sure you aim the hammer head so that the center of the head hits the midpoint of each ear so that no part of the hammer head doesn't hit the ear; 5. Hold hammer with two hands at the end of the handle and wack it with force enough to keep the hammer under control; don't baby it. Hold the hammer with the handle at your belly button, hammer head centerpoint of your chest; 6. When getting the wider rear wheels off, can't really wack it the same way; need to use much more wrist. The Trigo spinners are forged aluminum so the ears shouldn't snap off although they can get deformed. I am replacing one of my spinners that was slightly bent like a pinwheel and also flattened a bit. A lot of this seems pretty obvious but after to talking to 3 or 4 pros, there was more to it than I initially thought. I followed this technique in the Olthoff video for reinstalling (although my ear isn't trained to hear the sound that Bob referred to in the vid) https://www.youtube.com/watch?v=X8kCWG3d1Cc |
… or, you can do it the easy way. The wayyyyy easy way.:cool:
http://www.clubcobra.com/forums/all-...ne-finger.html |
Quote:
|
:CRY: I have blister on my hands trying to get mine off with a dead blow hammer ordered the 911 tool and muther thumper
Quote:
|
Quote:
|
Quote:
|
All times are GMT -7. The time now is 03:02 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: