|
I am interested in these seats. Can anyone comment on the difference between these seats and the Kirkey Vintage Class Bucket Seat? The price is not the issue. Also, can some one recommend a good passenger seat that I can install in my project that would look and feel good for the wife with on a Sunday drive. Would a Ken Miles seat be good for the passenger?
|
I have been told that that comp cars that ran these seats just had a "regular" passenger seat next to it, but if you wanted to spend the dough I am sure you could put a similar seat in the passenger side.
Kramer |
Has anyone used high density memory or other high-tech foam on these seats? Are they as comfy as the regular seats?
|
Lew
Yes we did use High Density foam in the bottom and the sides and the back....... The foam helps...... but the seat is not a good seat to use on a race track...... or long rides..... just doesn't support the driver or the passenger.... The Kirkey Vintage seat is much better and holds you in place much better. higher sides and better rib support. Morris |
Thanks Morris. My car is used on the street. It is my daily driver when its above 50 and below 85 and not raining. Is the seat more or less comfortable than the stock seat? I am trying to sit lower in the car as I am 6'4". I have more than enough leg room with the dropped pedal boxes, but I look over the windshield. I removed about an inch of foam from my stock seat and mounted it directly to the floor. I would like to sit even lower, but still want to be comfortable.
Thanks |
Lew
You bet .....adding the foam from Aircraft Spruce to the bottom sides and back of the seat made for a comfortable seat ........and in one of my post we cover how we did that...... on the seat you are talking about....... In the end it did get me lower in the car and was not a bad ride ....... the foam is the foam that pilots sit on for hours..... then we put the cover over the foam. And Lew thanks for the tip on the foot box a while back...... not only did we make up a plate for the feet to rest on but we put a 2" bar at the end of the plate to act as a foot rest and brace for your feet. Try this..... Kirkham Motorsports Automobile Club Morris |
Thanks Morris. I was leaning towards Aircraft Spruce. Your recommendation is very much valued. I might have a leather cover made locally and put GT40 grommets in it if that helps with ventilation.
|
Are these seats still available, can they be used with a seat runner??
thanks |
BMBC,
I will have to look up the guys contact information tomorrow, but when I get in the office I will send you his contact information. Kramer |
Hey Lew one of the big guys on here (MDMAN352) came up with a clever solution. I did some tunnel, footbox and exhaust mods and he had his upholsterer make up a cushion for the bottom and back. It looks like a Cobra seat but gets him low and back and is comfortable. I'll find a picture of it.
|
1 Attachment(s)
I love my racing seat. I'm not sure of the make, but it fits very snug.
It also prevents anyone with anything close to thick hips from asking to drive the car. Here's a shot. |
I had Steve make me one of these seats and really like it. The quality is very nice and I love the way I feel driving the car. If you guys are interested you should call Steve and ask about them...If my old contact information is correct his number is 201-213-2681. Let me know if you have any other questions.
PS...regarding the earlier comment on Kirkey seat....I think that is a good seat as well but I would hold the one I have up to it any day....MORE importantly it looks "right" in the car. Kramer |
Ken MIles seat
I have one of these seats for my Carbon Cobra. I too added the Aircraft Spruce material under the seat cover (Apollo tech vrs Space shuttle tech) BTW the seat cover that came with the Miles seat is very nice and goes well with the Shelby seat on the passenger side. And I have to argree the look is better than the Kirkey with the Workmanship on another level. Just too bad the nice plaque is in an area nobody will ever see.
Richard |
Are these seats still available? I sent Steve a PM, but haven't heard back. I am not sure if he still checks CC. I have one, but it was the biggest size that Steve made at the time. i ended up using a Kirkey instead. Since I don't track the car, I don't need all of the lateral support that the Kirkey offers. My main objective is to sit as low and as far back as possible, so that is why I am not using the stock seat. Since I ordered my Ken Miles seat, I've lost a bunch of weight, so if I could use a smaller version of the Ken Miles seat, I would buy one.
If anyone knows how they size these seats, I measured 18" at both the hip measurement and the back measurement as per teh Ken Miles seat measuring instructions. Does anyone know if this still equates to the biggest seat, or could I bump down a size? Thanks, Lew |
I have one that Steve made for me that I don't use if interested. I don't know what size it is but I can tell you that I am a 34 waist and it fits me just fine. After having it in the car for the past two years, I find myself using the stock seat more often. If you want mine, I will consider selling it to you.
PM if interesting and I can get you some pics, details, etc. Kramer |
I know it has been a while
Does anyone know if these seats are still being produced or have contact information? Thanks -- Jim
|
yes i would buy one of these seats as well
|
Steve sunshine made these seats. I have one. They are top notch and very period correct. I have not heard from Steve in about 8 years now. I doubt they are still being made. His contact info is here in his page.
|
| All times are GMT -7. The time now is 08:51 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: