 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
1 |
2 |
3 |
4 |
5 |
6 |
| 7 |
8 |
9 |
10 |
11 |
12 |
13 |
| 14 |
15 |
16 |
17 |
18 |
19 |
20 |
| 21 |
22 |
23 |
24 |
25 |
26 |
27 |
| 28 |
29 |
30 |
|
|
|
|
|
|
CC Advertisers
|
|
08-21-2015, 07:44 AM
|
|
CC Member
|
|
|
Join Date: Nov 2007
Location: Richardson,
Tx
Cobra Make, Engine: Antique & Collectibles, Forte 427 SB, TKO 600
Posts: 200
|
|
Not Ranked
Seat belt mounting options
Looking at picking up the 67 Roadster.
I was able to get an electronic copy of the build manual.
I was wanting to run a 4 pt. harness. I see in the manual where you can drill a hole at the bottom far rear of the cockpit to mount lap belts.
What about running the shoulder belts?
Just get one of those brackets and anchor them to the rollbar?
Or actually cut slots into the rear firewall and anchor them to part of the chassis?
Any pics you all could post up would be appreciated.
|
08-21-2015, 09:26 AM
|
 |
Member of the north
|
|
|
Join Date: May 2003
Cobra Make, Engine: A Cobra
Posts: 11,207
|
|
Not Ranked
I had saddle leather mounts made for the shoulder straps. They wrap around the roll bars.
They bolt on with 3/8 bolts and acorn nuts...look great.
No, I do not have pictures.
Tru
__________________
I'm a writer, feed the artist and buy a book.
|
08-21-2015, 10:42 AM
|
 |
CC Member
|
|
|
Join Date: Jan 2009
Location: Las Vegas,
NV
Cobra Make, Engine: Shelby CSX4005LA, Roush 427IR
Posts: 5,456
|
|
Not Ranked
__________________
Cheers,
Tony
CSX4005LA
|
08-21-2015, 01:53 PM
|
|
CC Member
|
|
|
Join Date: Sep 2007
Location: Marlboro,
NJ
Cobra Make, Engine: Contemporary Cobra
Posts: 904
|
|
Not Ranked
Seat belts
I have a A&C and the easy way is to get 4 clevis's 1/2" thread and drill a hole with a big fender washer and for the shoulder harness put a 1/2 bolt thru the upper shelf in the trunk with either a fender washer or I used a 4x4 peice of steel, I welded brackets to the frame instead of fender washers
Jon
__________________
The Impossible Only Takes A Little Longer
|
08-22-2015, 10:30 AM
|
|
CC Member
|
|
|
Join Date: Nov 2007
Location: Richardson,
Tx
Cobra Make, Engine: Antique & Collectibles, Forte 427 SB, TKO 600
Posts: 200
|
|
Not Ranked
Jon
I was thinking of doing something relatively similar.
|
08-23-2015, 06:09 AM
|
 |
Senior Club Cobra Member
|
|
|
Join Date: May 2001
Location: Florence,
AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
|
|
Not Ranked
I would strongly suggest all belt mounting points be attached to the frame. Even if you have to weld tabs.
I have seen a lot of seat belts in Cobras attached to fiberglass. The belts will not hold in a wreck. IMHO
Dwight
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
|
08-23-2015, 08:16 AM
|
|
CC Member
|
|
|
Join Date: Nov 2007
Location: Richardson,
Tx
Cobra Make, Engine: Antique & Collectibles, Forte 427 SB, TKO 600
Posts: 200
|
|
Not Ranked
Solid points mentioning anchoring the belts to parts of the frame.
Luckily, I work in a sheetmetal fab shop and have access to make and fabricate what I need.
Now than, let me ask this.
What would be a good brand of 4 pt. seat belts to buy?
And do most belts come with some kind of an anchoring stitched into them?
The Cobra will see 99.5% of it`s life on the street so, I dont need a radical seat belt mounting system.
|
08-24-2015, 10:09 AM
|
|
CC Member
|
|
|
Join Date: Sep 2007
Location: Marlboro,
NJ
Cobra Make, Engine: Contemporary Cobra
Posts: 904
|
|
Not Ranked
Seatbelts
Not to be combative on a safety issue
but several yrs ago I had a bad accident in a cobra... Seat belts were bolted thur fiberglass and held... No issue. Big problem which caused injury was the side pipe coming loose from the frame mount and almost coming thru the body. My pipes now have welded tabs on the frame and muffler and bolted together!
Jon
__________________
The Impossible Only Takes A Little Longer
|
08-24-2015, 10:42 AM
|
 |
CC Member
|
|
|
Join Date: Aug 2014
Location: Syracuse,
Ny
Cobra Make, Engine: Superformance #2660, FE-406
Posts: 372
|
|
Not Ranked
Any shoulder harness mount points should be at shoulder level or higher.
Mine are bolted to frame about shoulder level but rollbar mounting would be safer, assuming the bar is solidly frame mounted itself.
__________________
The older I get, the faster I was.
|
08-24-2015, 10:47 AM
|
|
CC Member
|
|
|
Join Date: Aug 2014
Location: Syracuse,
Ny
Cobra Make, Engine: Superformance #2660, FE-406
Posts: 372
|
|
Not Ranked
Quote:
Originally Posted by saltshaker
Not to be combative on a safety issue
but several yrs ago I had a bad accident in a cobra... Seat belts were bolted thur fiberglass and held... No issue. Big problem which caused injury was the side pipe coming loose from the frame mount and almost coming thru the body. My pipes now have welded tabs on the frame and muffler and bolted together!
Jon
|
Not to be combative on a safety issue but you are one lucky SOB. You should get the belts mounted properly. Really.....fiberglass? 
__________________
The older I get, the faster I was.
|
08-24-2015, 03:03 PM
|
|
CC Member
|
|
|
Join Date: Sep 2007
Location: Marlboro,
NJ
Cobra Make, Engine: Contemporary Cobra
Posts: 904
|
|
Not Ranked
Belts
I now have welded tabs
Jon
__________________
The Impossible Only Takes A Little Longer
|
| Thread Tools |
|
|
| Display Modes |
Rate This Thread |
 Linear Mode
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 04:14 PM.
Links monetized by VigLink
|
