|
Garage Update # 15
The roofer did their stuff last week and it looks like this,,,,,,,
http://www.clubcobra.com/photopost/d...m/DSCF2452.JPG http://www.clubcobra.com/photopost/d...m/DSCF2453.JPG http://www.clubcobra.com/photopost/d...m/DSCF2454.JPG http://www.clubcobra.com/photopost/d...m/DSCF2455.JPG http://www.clubcobra.com/photopost/d...m/DSCF2456.JPG http://www.clubcobra.com/photopost/d...m/DSCF2457.JPG The builder and sparky started back today, I think they have already left as its bloody HOT today. STIFFY |
"Hot enough to boil a monkey's bum, your Majesty he said"
|
Stiffy, great work. Just a quick question. In the 1st and 2nd pics the lower roofs butt up against the pine uprights that extend up to hold the main roof. Shouldn't there be a flashing that runs up the pine 200-300mm that would get covered by the wall cladding and under the iron on the lower sections by a similar amount?
Regards. |
Are you sure that this isn't the new Melbourne Cultural Centre? It is huge!
|
Roof
Mando,
Well spotted, they left them on the factory floor and delivered them last week. They fitted them today. The sparky did alot of the set out and the builder did a bit before the heat arrived. STIFFY |
What are those flashings for? Pardon my ignorance.
|
Electrical Work
Modena,
The flashing is so water will not leak through the blue board ( I think ). Some more pic's, Flashing attached http://www.clubcobra.com/photopost/d...m/DSCF2490.JPG Mr Postit Note:LOL: the sparky wanted all the points and lights marked,,, http://www.clubcobra.com/photopost/d...m/DSCF2489.JPG Bogger & Shower http://www.clubcobra.com/photopost/d...m/DSCF2482.JPG The Bar http://www.clubcobra.com/photopost/d...m/DSCF2480.JPG The marked walls http://www.clubcobra.com/photopost/d...m/DSCF2479.JPG The grinding/welding room http://www.clubcobra.com/photopost/d...m/DSCF2478.JPG STIFFY |
Stiffy,
Providing a penetration for ventilation in the grinding/welding room? Cheers |
yes that looks like it makes sense, I didnt think it would go UNDER the tin
|
Vent
Krait,
You obviously haven't seen me weld :3DSMILE::3DSMILE: Yes there will be a vent, just need to get the final inspection done..... just like building a car really.......:JEKYLHYDE:JEKYLHYDE STIFFY |
| All times are GMT -7. The time now is 03:22 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: