|
Clearance Issue Help!!!
Hi Guys...
I'm building an old GForce kit. I have Jag front and rear already in. Perfect fit... I have dropped in a 302efi from a NC Fairlane but I have an issue. Firstly I will to remove original gearbox mount put in by force to help locate and lower g/box. But my issue is the egi manifold. My bonnet won't clear. It hit the manifold right where the ECG valve is...I need about 50mm of clearance to close bonnet properly. Even though when I eventually lower gearbox into correct position this still won't clear properly. Can anyone she'd some light on this... any elbows I could use. Anything? |
Can you show some pix so we can see the problem better?
|
Have a look at this build thread. G Force with a 5.0l injected motor, maybe contact Slowy and ask for help.
http://www.clubcobra.com/forums/aust...ra-update.html |
3 Attachment(s)
Quote:
Regards Wil |
I'd need to go back and try and find out what engine mounts I used but suspect that might be a starting point for you. Wrong mounts and the engine would be standing taller in the engine bay.
As Albanycobra has linked, my 5L with the standard plenum fits easily. My only bonnet clearance issue is that the outer moulded rail on the underside of the bonnet has been touching the intake tube. It hits just on the bend just before the plenum intake point as seen on the second pic in the link. A quick look in my file and have found the invoice for a pair of Mackay engine mounts ,Burson part A1140. I've hand written Ford Falcon, Fairlane 8 cylinder 1966 onwards as the source. Does this help? |
Guys thanks so much for your speedy input... I used standard mounts more or sits pretty. I have a 10mm gap between oil filter and chassis rail. So goin lower may not be an option here. My friend has a newer GeForce kit and same donk and it clears only just. There is however a difference on the inner skin of his bonnet than mine... Perhaps a different manifold may do the trick. I will look into it further...but again thanks so much for help. Ps I will try and post some pics of the clearance issue.... If I can work out how to post them lol...
|
What oil filter are you running? If you have a Z9 fitted swap it to a Z89a that's the shorter AU falcon 5.0l filter and will buy you 40 or 50mm.
|
My cobra has a BA GT bonnet bulge grafted onto the bonnet as I am running Eidelbrock injection on a 5L SVO, jag front and rear, standard engine mounts.
Very tight bonnet to intake clearance but just enough. |
Or use a remote filter kit??? They pretty cheap as well
|
Yes I've also got a remote filter set up.
This as I could only fit the small Z filter in-situ straight off the block without hitting the chassis. But also because I am using the standard AU oil cooler which necessitated use of a sandwich plate anyway. Work at lowering the engine first though as this will help car balance. Use of a remote filter or even grafting say a slightly larger scoop are jobs that could be done later without great difficulty. |
Ongoing clearance
So I get this right...
Use remote oil setup? Lower engine via lower engine mounts? Shollower sump to gain ground clearance? Perhaps modify inner bonnet skin? I looked up Elderbrock Victor, but showed me intake manifolds... Do I need a lower intake or a different plenum and air intake setup? Sump and ground clearance at the moment looks right... I'm really not wanting to lower engine, I need to shave the 40mm off the height off bonnet and plenum combined.... Hahaha the torture never stops guys... This is joy of building something like this... Loving it, loving the fact you guys are out there... Cheers |
I believe
engine mounts for XW-XY will do the trick, |
Hi bohemath777
PM sent |
Hey Lex...
Can you please tell me how to view your PM. Apologies as I'm new to this forum... Is emailing me direct easier. Pettas66@Gmail.Com Again apologies for the hassle. Love your input in helping me out. �� |
Just go to the top of this page and there's a horizontal narrow mid blue menu bar in the top box, with : Portal, UserCP, Blogs, FAQ etc... Hit UserCP and you get a dropdown menu, and select Private Messages at the top.
From here you can receive and send messages. I common fix for your issue in the early days was to cut a large relief hole in the bonnet and fit a wider scoop - as per factory DRB. I reckon its worth the trouble to lower the engine and or change manifolds. Achieves a far better look. If your only after 40mm, a bit here and a bit there shouldn't be too hard to find. Some guys used to cut one of the rubber layers out from an XY mount and weld the mounting plate back to the middle plate, then drill through the centre and fit a 7/16 bolt with lock nut just a thread or two from tight for good measure. This bolt set up was an old speedway trick to prevent the engine from tearing loose if the mount failed. |
| All times are GMT -7. The time now is 11:10 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: