|
Jaguar front end reconditioning
Hi all,
Pulled apart my jag series III bits and have a couple of questions. One stub axle is showing signs if wear at the inner bear race position. Its about 0.1mm worn on one side (ie the wear isnt even the whole way around). Am I best off replacing this? If so, is there a trick for getting the axle out of the knuckle? Its jammed in there tight? Also, Whats the wear tolerence on the rotors. Mine are down to 23mm beofre getting them machined. Have got the calipers apart and am replacing all the seals. Repco wanted to charge $160 all up for the full set (Im pretty sure that was a little over the odds!!). Off to ebay, AU$36 delivered from the US. Ebay is quickly becoming my best friend. Cheers, Andrew |
Tenrocca, I had to take my stub axle to a workshop and have the thing pressed out.
Easy to get back in, just tighten the screw, but getting out neede to be pressed |
I got my seal kits from Western Australia.
Unfortunatly I dismantled my calipers and threw out what I thought I wouldnt need, I tossed out the round steel clips that hold the outer dust boot to the caliper, the new kits I bought didnt have new ones, so keep your old ones. If your new seal kits have new clips I will buy the old ones of you if your gunna toss em out. P.s Andrew, check your pm list I sent 1 about a week or so ago. |
David,
99% sure the kit I ordered has the clips so you can have the old ones. Just checked the PM. You have an email cheers, Andrew. |
I got my seal kits from Thompson's (Part of Coventry group) $15 for 2 sets I think (rears).
I needed one new brake retaining clip, which cost $25 from a Jag outlet!!!! Worth getting your inboards (rear) sorted before fitting to the car - major dramas otherwise thats presuming you have that setup. |
The Classic Revival kit doesnt use the jag rear.
|
Shame - it would be a smooth ride.
|
HAHAHAHA you jag lover you.
The Classic kit uses the rear from an AU irs falcon (damn Ford part had ta find a way in there somehow) I am yet to see how it feels on the road as mine isnt going yet. But I am getting better at the Broom Broom noises now that I have a seat, a wheel, a gearstick and pretend dash. |
Got the stub axle out using a pointy chisel and a baby sledge. One good swing got it in the end. :D
Still wondering though if the rotors have enough wear left in em or wether I should just replace them with newbys? Im guessing they will be down to about 22mm once machined? David, seals kit came yesterday and included clips, so Ill send the old ones off today. Man, the kits still 4 months away and Im already lovin this. Got the skinned knuckles to prove it. :D Cheers. |
Right there with you Tenrocca. Chassis is arriving on Saturday (I hope) and I am already into the second jar of hand cleaner. Front end and back end just about ready to bolt on.
Gotta keep the hands clean for my pen pushing during the week. We are probably going to go with big Brembo's on the front, been out to race brakes at Wetherill Park and the guy seems pretty good and has already done a whole bunch of CR's. |
I have just checked the rotor book and it says series 3 rotor minimum thickness is 22.9mm
|
Thanks David. I was leaning towards replacing them so thats made my mind up.
Cheers. |
Does anyone know of anywhere other the www.ppc.com.au that sells por-15 off the shelf? Id like to pick some up tomorrow but dont fancy the drive to the Northern Beaches. Otherwise Ill just order online and wait.
David, did you get the clips OK? Churchy, you have a PM. General forum question, are you supposed to recieve and email when you get a PM, cos I never do? Go the Tahs this Sat!! |
POR 15
TENROCCA
I sell Por15, PM me I can tell you where to get it direct or I will get it for you Regards Bazz |
Tenrocca, just sent you the reply to the PM. General forum answer. emails for PM, I never do either, but I have the option turned on... ???
PPC (POR15) I orderded from him and he delivered the next day, however if Barry sells it give your money to a forum member. I can certianly vouch for POR15, really good stuff. One other point, I totally concer with "go the tahs", what a game on Friday night... arrhh when too much Rugby is not enough |
Yes I got the clips on Friday afternoon, thanks for that Andrew.
I didnt get a chance to say so earlier as I had a quick trip to Adelaide (flew out of Alice 4.30 pm Friday and flew out of Adleaide 9.00 am Sunday) If I was staying longer I would have made in known I was coming down. I had to attend a function for Toyota and was put up at the Stmaford grand in Glenelg, Black tie formal event, they paid for myself and my wife to be there. While we where there I saw rain for the first time since Goulburn (gotta love the Cobra weather out here) |
No worries David. Just wanted to make sure They didnt get lost somewhere between here and the Alice.
Rain....what does that look like again. Were in for next level water restrictions in Sydney soon. I think what means you can only p1ss every second day. |
I have always got an e-mail notification for PM's. Can't see any where in the control panel to turn it on or off.
|
Just found it. Go to user cp, then edit options. Theres a check box to recieve email notification for PM.
Cheers |
| All times are GMT -7. The time now is 09:34 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: