Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Classic Roadsters II (http://www.clubcobra.com/forums/classic-roadsters-ii/)
-   -   Stripe Dimensions (http://www.clubcobra.com/forums/classic-roadsters-ii/19899-stripe-dimensions.html)

BrianBhoy 08-31-2002 03:57 PM

Stripe Dimensions
 
I would appreciate any details on recommended stripe spacing and width for a classic roadster. thanks, Brian

petek 08-31-2002 06:45 PM

Do a search here for the ERA striping diagram. I used it on my CRL Cobra and it looks great.

Double Venom 08-31-2002 07:55 PM

Brian,
First thing you do is find "center". Easy to do if you drop the windshield in place. Then use the two lower holes in the frame, find the center there and wal-LA!

I simply take a 2" roll of masking tape and run it front to back, in one long strip using the center mark to line things up. Then from the outside edge of this strip, at the dash area, I mark out 11"s. I then run the tape foreward to the nose, "tapering" the front down to about 8 1/2"s.

I also start to taper the rear down, from the front cowl almost immediately. The outside edge of the rear stripe ends up just about 3/4" from the trunk edge.

Hope this makes sense!

http://pstr-m04.ygpweb.aol.com/data/...3fP7qb0180.jpg
DV

BrianBhoy 08-31-2002 10:36 PM

Pete and DV

Thanks for the advice...pics will follow by end of September!

Regards,

Brian

Snake 09-02-2002 01:42 AM

Hey BrianBhoy !
 
Cobra Stripes For Classic Roadster's Cobra

Here are the cobra stripe diminsions for a Classic Roadster that correspond to the original stripes but are enlarged to meet the longer and wider wheel base.

front bottom to bottom of opening
(including oil cooler) 6"
top of front opening to engine comp 7"
hood scoop opening 7 1/2"
back of hood 8"
passenger compartment 8 1/4"
passenger compartment back 8 1/4"
top of trunk 8"
trunk down 10" toward rear bottom 7 3/4"
top of plate holder mold 6 3/4"
bottom of trunk 6 1/4"
bottom of car 6"

Also, the inside of the engine compartment and trunk compartment was treated like an overspray with the paint only going 1/4" down, not the entire depth of the mold. No stripes were under the hood or trunk as some I have seen.

The width of the space between the stripes is still 1" but can be widened to 1 1/16" depending on how you feel about it.

Sorry for the delay,
jayscobras
jay


I got this from Jay awhile back.....maybe could help you out.
Snake.


All times are GMT -7. The time now is 06:43 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: