|
bmcnicho, roll bar
Buddy you kind of left me hanging. Didn't want you to write back and say where the heck is it"?
If you don't want one now- no sweat, just let me know. To exspensive to just hang them on my shop wall! :) DV |
I'll take one
Sorry for the delay. I have been working on getting quotes to finish the work on my cobra and haven't been checking the forum. I will take 1 drivers side rollbar prepped for chroming.
I will put a check for $325 in the mail tomorrow (1-22). |
OK then, I'll start getting it prepped and will let you know the minute I ship it!
Thanks for the order! DV |
How is the roll bar coming?
How is the rollbar coming?
|
"B",
I hate exscuses, especially in this business, but twice this week I have had to offer an apology. I had one small and final bend to the down leg on your bar , A tweak really,( didn't bend it far enough the first time),, and I blew out a small "O" ring on the bender. Capteddie has made the arrangements to get it fixed over a week ago. I sent the pump back and awaiting for its return. If I get it early enough I should be able to add 2's to the bend and get it in the mail that day. Sorry, but it is on it's way....almost! DV |
DV...
Anything you need me to do with regards to the pump? Do I need to make a call? Just let me know. Ed |
cpteddie,
We're good, just waiting for the return. So aggravating..... I look at the down leg already bent (not far enough) and I think if only I could put out ten tons of force I could just grab both ends and bend it the two more degrees and it would fit right in! ;) DV |
DV,
Any status update on the rollbar? Best Regards |
'B',
Just showing my stupidity at times: Quote from cpteddies post BENDER: What a screw up! I mailed it and was getting a little cranked because it hadn't shown up yet! Finally it came back Sat.---just like I sent it! Seems the box,( A cut down " AUTOZONE OIL QT. SHIPPING BOX) didn't quite meet muster for the P.O., seeing that the box said in numerous places "12 qts. 30 wt. oil! They sent it back even though the box had ben cut down to fit the pump! I taped up all offending EPA shipping info and RE-SHIPPED IT IMMEDITELY. Not holding up your job but it sure isn't helping ('B') get his roll bar! DV Dammm stupid 'S' happens-sorry. DV |
Your expertise and connections are requested.
Hello again.
I am looking for parts, and need help with: The hidden latch assembly with cable for a CR Roadster A phone number to contact (to give to my friend who is helping me) for parts and any other advice needed. (I had pulled the Chevy engine to put in a 361/C6 combo so it would sell fasted when I was finished, but before my friend got around to building the 351, he determined that 351 headers were no longer available. The Chevy is back in and of course, I now know where a set of 351 headers are... oh well) This build has been on for about 4 years now. Any help is appreciated now that I am down to the "little things" ie: Power steering Narrow rear end 3/4 and 3/8" Install heater Install radio Install Auto dimming-compass/Temp/Home link rear view mirror Get final inspection from State.. Drive home Sell.... Thanks for anything!!! John Carter 612-867-4000 |
Rollbar seals?
Hey DV,
I have a full width rollbar from CR. The rear legs dictate a very elongated ring because of the angle. I'm making my own since I can't find any to work. Is that my only course of action? Thanks. -G |
"G"
Here's what DV made for me. The back supports go in close to a 90 http://www.clubcobra.com/photopost/d...er_coat_f_.JPG I'll be at DVs on Saturday if you want some additional photos. Cheers! |
Finishline has elongated grommets and finish rings for the rear, I believe they are for a 2" bar.
DV |
Capteddie,DV,
I wish I had the DV rollbar. Sure would have made things easier and more structural. Unfortunately I have the CR bar and the back legs are at too much angle to use the Finishline rear grommets.(Which I already have) Guess I'll start cutting aluminum and rubber. WE SHALL OVERCOME! Thanks. G |
G...
If you make some, make a pattern for yourself! A lot of guys would like to have the grommets that actaully fit! DV |
G,
I have the full-width Classic roll bar as well -- the Finishline rings/grommets fit very nicely. Dwain |
How is the roll bar coming?
Do you have ETA for the rollbar? I am at a point where it is a kind of holding up the build. :CRY:
|
Quote:
Hang in there.... |
I just spoke with the guys in warranty repair at SPX Fluid Power and the bender pump should be fixed by tomorrow. Then they'll ship it back to DV.
DV.... As soon as they give me a tracking number, I'll forward it on to you. |
Rollbar?
It's been a couple weeks. Do you have the bender? It has been 3 months since I ordered the rollbar.
I have found another source for a rollbar. I would love to get the one from DV, but if you can't have it soon can I refund? I hate to nag, but the shop working on my car is asking about it a couple times a week. |
| All times are GMT -7. The time now is 09:32 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: