edelbrock performer rpm intake vs victor intake

[Cobra #3170]

Originally Posted by blykins

All dual plane vs single plane arguments go out the door when you're talking about 482 cubes. If this was a 352 or a 390, my answer would be different, but an engine approaching 500 cubes can get away with non-typical items. The same idea applies to small blocks. A 351W would be a little fussy with a Victor Jr or Super Victor intake, but a 427/445/460W would be right at home with one. They need the extra plenum volume and can handle the demands that a short runner places on a smaller engine.

If you have the room under the hood, my vote is the Victor FE. You can still have a very nice streetable engine with a single plane intake...I promise.... Let the cam put the peak where you want it, run plenty of advance in the cam timing, and let her eat.

I agree with Blykins 100%, I have a Victor Jr. and it produces plenty of torque at all rpms with a 1600CFM throttle body. The last thing you need in a Cobra is more low end torque, especially with big CID FE. Go for the Victor you won't be sorry, I even had a 1300 Dominator on it that worked well too.

I have run single and dual plane manifolds with both dual fours and single fours on a number of FE's and I always liked the single plane manifolds the best.

[fordracing65]

Like is said before, #3170 I agree with your opinion on cobras over all others, the only problem with the Victor is getting it to fit under the hood, I will be using a 950 carb.

[Cobra #3170]

Originally Posted by fordracing65

Like is said before, #3170 I agree with your opinion on cobras over all others, the only problem with the Victor is getting it to fit under the hood, I will be using a 950 carb.

The Kirkham engine mounts are little taller than original, you might be able to gain something there (make your own) you can also mill the carb mounting flange and gain some there. If you have a hood scoop you can use some of that real estate to fit a custom air cleaner. I have a hood scoop and am partially into that area with my air cleaner, but I have a 1" Wilson spacer on the manifold along with their throttle body, I am pretty sure the total height is greater than a Holley carb. Check out their engine mounts they are a great design just too tall. I'll measure the distance between my china wall and the edge of the body that would be flush with the hood and send it to you tonight.

[Cobra #3170]

Originally Posted by Cobra #3170

The Kirkham engine mounts are little taller than original, you might be able to gain something there (make your own) you can also mill the carb mounting flange and gain some there. If you have a hood scoop you can use some of that real estate to fit a custom air cleaner. I have a hood scoop and am partially into that area with my air cleaner, but I have a 1" Wilson spacer on the manifold along with their throttle body, I am pretty sure the total height is greater than a Holley carb. Check out their engine mounts they are a great design just too tall. I'll measure the distance between my china wall and the edge of the body that would be flush with the hood and send it to you tonight.

It is 13" from the FE china wall to the cowl top at the hood center line, my manifold, spacer, throttle body and air cleaner stack are just below the bottom surface of the hood at the rear.

[fordracing65]

Thank you so much #3170, when I get my car done lets race. lol

[blykins]

Maybe the Kirkham boys will cut the motor mounts down for you a bit....I don't know how bad it would mess with the trans mount and pinion angle though. Might wanna ask Tom/David.

I can mill quite a bit off the Victor intake for you, so that's no problem. The Victor requires quite a bit of work to be really functional on an FE anyway, so one extra step isn't gonna kill anyone...

[fordracing65]

Originally Posted by blykins

Maybe the Kirkham boys will cut the motor mounts down for you a bit....I don't know how bad it would mess with the trans mount and pinion angle though. Might wanna ask Tom/David.

I can mill quite a bit off the Victor intake for you, so that's no problem. The Victor requires quite a bit of work to be really functional on an FE anyway, so one extra step isn't gonna kill anyone...

Just as long as it does'nt get so crazy I loose performance and run into unforseen problems down the road beacause of so much tinkering.