How did you mount your rear license plate?
Need some advice on how everyone is installing their rear license plate. Reason is the Texas plate will not fit between the license lamp fixture and the trunk handle. We ended up mounting it on the bumper rails and really don't like it. It appears Midstates did not take this into consideration when designing the spacing. Any suggestions from fellow Midstates owners?
Mike |
Tag bracket
I don't have a Midstate but I have made stainless tag bracket for a few of our Cobras. Mine is a Lone Star and I made one for Mike's FFR and Hurricane. I use angle and/ or flat stock. Weld up what we need and polish till it shines like chrome.:)
Never had one of these to break and drop a tag. Dwight http://www.clubcobra.com/photopost/d...m/DSCN3851.JPG http://www.clubcobra.com/photopost/d...m/DSCN3850.JPG |
Red......you have a message,,,,,,,,,,,,,,Ron
|
I just did a little trimming on the plate itself - got the idea from Bob's car...
http://www.clubcobra.com/photopost/d.../license_2.jpg |
Mine is trimmed like ZIPZIP,s. It is not the Texas license plate, its the spacing between latch and light. See my gallery.
|
The reason that the plate doesn't fit is because the original cobra is european and their plates are much narrower, most cobra replicas are keeping the original lookand therefore U.S. plates are to big to fit. Finishline sells a plate hanger that is angled out to clear the trunk handle.
http://www.finishlineaccessories.com...abb37134da27a5 |
My midstates (built in 1992) is done just like zipzip. Bolts go through the trunk lid. Notched the plate to fit over the handle as shown in zipzip response. This is mor like the oroginals than the lonestar above where they have a large bulge, higher up on the lid.
just notch the plate and you'll be OK. |
I knew you guys would recommend the trimming solution which I did think real hard about already. We were hoping someone had figured out another clever way. Never know, we do have some clever folks out there.
Thanks to all for your suggestions. Really like your bracket, Dwight. Really sharp design. Well we will be thinking about this some more as we would really like to get this plate off the bumper rail. Mike |
http://www.clubcobra.com/photopost/d...runk_small.jpg
Mike...shave the trunk...makes the problem disappear...:LOL: Regards Glyn |
Finishline offers a bracket that may help.
|
I trimmed mine top and bottom.
|
Mine is off to the left. I didn't like it under the trunk handle.
:D |
Tags
Glyn
What type of fiberglass did you use to rework the tail light area? I took a better picture of the tag bracket today. Dwight http://www.clubcobra.com/photopost/d...ainless_2_.JPG |
I took the handle off the trunk, drilled a hole in the plate and mounted the handle throught the plate.
|
Dwight...just regular old fiberglass sheet and resin. Cut away ALL the light area and then laid down multiple layers from the inside until it was all done, then sanded inside and outside and smoothed with 'bondo' filler.
Of course, you have to add a 'hidden' trunk pull then to open the trunk! Glyn |
All times are GMT -7. The time now is 09:32 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: