Mike,
Glad to see you getting after it. Best, BC |
Quote:
Thanks Again, Mike |
1 Attachment(s)
[quote=rustyBob;1129452]can you post a pic. of what you have.....
QUOTE] Sorry it took so long. Here's a pic of the lower control arm looking forward from underneath. Notice it's pivot point in in front of and inboard of the frame rails. -Mike |
No thats ok i know how time gets away from you when you're busy.....
OK yours is like that because you have the round tube frame....i have the 2x4 tube frame and there is a kick up on mine at the front that will let the lower control arm to be wider where it attaches at the front crosmember....so you may be stuck with what you have....or there are some round tube lower arms that will fit in where the originals go and you can still run the strutrod... |
Geez Mike great build log. I see what you're talking on the fronts now. Why don't we make some arms shorter and conventional mounted? You've made and customised everything else! Thanks for the good press. That pinion angle I listed is on the other CCX thread but I guess they didn't read or believe it.
|
Quote:
Quote:
Thanks |
Progress Report..
3 Attachment(s)
No, I did not abandon this project!! :LOL: Just have not had time to post lately. Here goes!
Fabbed up from scratch new top and front cross members to mount the Jag IRS. This also involved painfully stringing out the car to make sure it would align properly and also have the correct 90 wheel base. I have done most of this work with a dewalt angle grinder with a cutting wheel installed. It slipped out of my hands while making the new cross member and almost removed all of my internal organs. Thank God for the heavy welding shirt I was wearing. Note to self, cut with the flow of the wheel not against it. I mocked up a test fit prior to the final welding using the unpainted dirty rear end and some old aldans shocks on one side.. Tires fit nicely and rear is centered in car with about 1/16 toe in on either side! I adjusted toe using some GM starter shims between the fulcrum arm supports and diff. The starter shims worked perfectly. If you look closely in the last pic you can see the mickmate OEM spec rollbar lurking in the background.. Schweeeeeeeett! |
Top Cross member.
1 Attachment(s)
Rear end removed for clean up and new cross members fully welded and painted. Wow, this has been some tedious work so far. Not so much the fabbing, but making sure that the rear end is in square and the ride height is acceptable.
|
Cleaning up the ole dirty rear and rebuilding the brake calipers.
3 Attachment(s)
I cleaned up the rear diff, replaced all of the seals and gaskets and painted it. I also bead blasted, honed, rebuilt and painted the brake calipers. The outer dust seals were a royal pain in the @SS to get in... Wheres the tylenol when you need it?
The Diff is a 3:31 posi traction unit. Upon inspection all of the internals & gear looked great. Looks like a pretty strong diff to me! |
New Half shafts
1 Attachment(s)
New Half shafts.. I had a local drive shaft shop fab up some new ones using DOM tubing that I aquired online. I hope I have enough HP to spin them over. :LOL: These babies are beefy. I also ordered some new spicer u-joints online and pressed these babies in. The spicers were a very tight fit, almost like they were a little longer than the stock jag ones. I really had to work to get the retaing rings in.
|
Looking good Mike, keep up the good work....any ideas on the front susp. or you just going to leave it alone ??..you could make new a arms....
|
Quote:
I'm going to try and get the car driving with the new rear first and then tackle the front once the rear is all ironed out. I do plan on pulling the body at a later date as well to give her a coat of Guardsman blue but I want to iron out all the bugs before final paint. I'll be working more on the Acton Custom Dash along with my custom trans tunnel supports, OEM split wheel, Smiths Gauges, VW turn Stalk and Kirkam Steering column next. Stay Tuned! |
sounds like you are going to be busy....
|
Been Busy.. Turning out Nice!
5 Attachment(s)
Rear is In...
|
More.....
2 Attachment(s)
More Pics... It ROLLS! Out in the driveway in the first time in over a year!
|
Roll Bar and Body Work Time!!
5 Attachment(s)
Wheh!! What a pain...
|
More Body and Paint....
5 Attachment(s)
More Body and Paint....
|
Acton Dash Time...
2 Attachment(s)
Covered her up in vinyl and put the gauges in...
|
Sorry for the sideways pics earlier...
2 Attachment(s)
Rotated em!
|
Trans Tunnel Mock, Steering Support Mod & Lucas Ign Sw.
3 Attachment(s)
Trans Tunnel Mock, Steering Support Mod & Lucas Ign Sw.
|
All times are GMT -7. The time now is 07:40 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: