|
Need Some Opions On Brakes!!
i am rebuilding an older NAF car. the guy who built it originally was not exactly a cracker jack when it came to mechanics. he used a set of neil pedals and master cylinders, both of which were the wrong size bore and both much to small for the car. and to boot, he had the smallest bore on the front brakes. oh well, that's why i am rebuilding. my question to all the experts with more experience in this than me is, what type of master cylinder system do you prefer? the balance bar set up with 2 masters for the brakes and one for the clutch , or a domestic type master cylinder and hydraulic clutch? i had thought of going with a power assist set up, but if i didn't. what recommendatuons would you make? i appreciate any help and information i can get. all opinions welcome. i have always gotten some great help from all the guys in this cobra club in the past...thanks . you can email me at tchrome@aol.com or post here. thanks again
tony |
My car has Wilwood pedals/masters. Nice set up and adjustable. You might also look into what other products Neil has to offer that might bolt into the setup you have already.
HTH Larry |
Given the one-of-a-kind nature of each of these cars, I think it is essential to be able to adjust the front/rear brake bias. Twin brake master cylinders with a balance bar is not the only way to do that, but it does work well. .. If you go with a system with aluminum master cylinders, be sure the rods connecting the pedal to the pistons are well aligned. If it is not, you may get accelerated wear on the bore of the piston and leaking.
|
thanks guys for your input. i havebeen leaning in that direction, although i have been seeing more and more of the latest cars being sent out with power assist units. have you heard much on how this is working out? i have heard of guys using a corvet master cylinder with a small power assist unt. thanks.
tonyh |
Go the twin route. Email me and I will send you some thing to help make your choices.
|
Tony -
Perhaps its because I've been driving my 1963 Corvette without power brakes for almost 30 years, but I don't see the great need for power brakes in my Cobra. I drive it hard at open track events and manual brakes feel fine to me. |
I just re did my brakes. I went with Wilwood rotors and 4 piston calipers.
The dual M/C is the way to go. You may actualy want the smaller M/C on the front. It seems backwards but you don't need volume (larger M/C bore) you need more fluid presure (smaller M/C bore) In my case I now have 3/4" M/C's on the front & rear sides. The realy big improvement came with the 4 piston calipers. The old 1 piston with the slide mount was realy bad. I think my pedal effort is down by 30% to 40%!! I bought my front brake kit from HotrodsUSA.com It has new hubs, bearings, 11 3/4" disks, mounting brackets and the 4 piston calipers. This set up still fits inside my 15" wheels. It is designed to replace Granada rotors on mustang 2 spindles without changing the offset. As an extra bonus it shaved 16 pounds of weight PER SIDE of the front.:eek: 32 punds total. It went together perfectly and now that everything is seating in it is terrific.:D |
Hi Tony,
Hey A COBRA GUY, Which kit did you use from HotrodsUSA? Do you have the part number? If not, the width of your rotors would be a great help. Thanks, Byron |
I also have the hot rod usa kit
It is for the mustang II spindle and 15" wheels. The kit has special wilwood zero offset aluminum hubs. The owner of hot rod usa asked wilwood to tool up for these hubs as they are not in wilwoods standard mustang II brake kits. The brakes are awesome...I opted for the larger front 4 piston calipers. Check out my gallery for pictures.
|
i have a NAF car , north american fiberglass. and i am running a stock mustcang 2 front end with rack & pinion. i think i am going to go back with the neil pedals and mastercylinders 3/4" bore all the way around. my other thing is to maybe get a ford or corvette master cylinder and go with that. but i like the originality of the the other set up.
tony |
Steve is correct that it is realy a custom Wilwood kit. I chose to go with smooth rotors (Not drilled or slotted) and the "standard" 4 piston calipers. This set up cost me $900.00 plus I bought a new M/C for about $50
The kit was part #B1F2427401Z. A plug for HotrodsUSA. They were great to deal with. Up front about delivery time but that did not slip from there origional estimate. Very helpfull with questions I had durring the research phase. Now a word about M/C's My car started life with the dual MC setup. While trying to improve things years ago I went to a larger MC for the rear. It helped a bit. During this winters upgrade I suspected I would need to re-size the MC's. The Tilton website (Tiltonracing.com) has a questionaire that asks all the details about your application. Weight, wheel base, driving style, and lots more. Fill in everything and in a week or 2 they email back there recomend MC sizes for front and rear. That is what I used to decide that 3/4" front and rear woukd work for me. VERY helpfull. |
Tony, don't buy the other ford/vette master cylinders etc. You can spend thousands and end up not satisfied. If you are willing to put the time in, I am willing to help.
|
Listen to Rick he's been there done that! give him a shout he knows what he is talking about
|
Quote:
|
Quote:
|
Quote:
|
| All times are GMT -7. The time now is 04:45 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: