Best way to proceed with improving up 427 Windsor street setup
I wasn't sure exactly where to post this so I will start in the small block section. Having recently purchased my first cobra I am really enjoying it and I can't see myself going to any other toy. I came from an 03 supercharged mustang cobra and the only thing I miss is the throttle response and the feel of the mod motor power. I put a new QF750 carb on my car and had it dyno tuned a few months back. My car runs night and day difference but it is not where I want it to be. I have a KC 427 dart block that I think is in need of a refreshen.....cylinder pressure is down a bit and it didn't do so hot on the dyno. This is not something that is pressing as the car runs great but I just want to start making my plans for the next step. If what I am after is not possible then I will re-evaluate. Hopefully we can have some good info out of this discussion.
1. I hate getting 9-10mpg. It is really not about money so don't bring up the "your not a cobra guy" it is just a pain in the butt. I've got 3:23 rears and a TKO-600. It was 7mpg before I had it retuned. Return on any type of investment is not something I'm chasing....but I do know that fuel injection will improve this. 2. If I was to go the fuel injection route how good can the throttle response and overall driveability be? Can it be similar to a N/A modified LS7 in a Z06? If so what is the fuel injection route that would be needed? I do not want to use one of those wet manifold self tuning carb looking setups that cost $2500 but I also don't want to use anything that is unnecessary. I could care less about how vintage it looks under the hood....I bought the car to drive and I'm looking for the best possible setup for reliability and performance. 3. I really would like to be able to keep a windsor setup as I enjoy the sound and characteristics of having a camshaft and all the lope that accompanies. This is a street car and I have no future plans on tracking it. This is Keith's 585hp option and I dont' think it deviates from their street/strip setup. Based on the current characteristics of the car it doesn't like to be driven below 2000rpms and it doesn't really have a serious seat of the pants feel until about 4000rpm and up. Being a street car I dont' have any pipe dreams of turning 7000rpm but I don't want to lose any top end power.......I actually want some more. I've never had a N/A setup before so I guess I'm just used to the power of a supercharged mod motor. Sounds like if a Windsor can offer what I'm looking for then Brent Lykins is the man to put together a plan. |
What did your 575hp KC 427ci dyno in at?
As for FI call Bob Reems at Imagine Injection. Imagine Injection Inc. | |
If I may, do you want to play with the engine or have someone take it to the level you want?
Tru |
You're going to have to give more detailed info before anyone can suggest any changes.
whats the mileage on the engine ? What cranking compression numbers are you seeing? What was the dyno HP ? What is your 5th gear ratio?. |
I know you say you are not interested in racing, but is there a local drag strip you could make a few passes at? 1/4 mile time slips will tell a lot more about where you are in real world performance that dyno slips.
|
Quote:
Quote:
Quote:
Quote:
|
Before you even think about changing to fuel injection, make damn sure your engines internals (cam) will be suitable for FI.
Contact the engine builder and see if it's compatible. If not, then you're in for some expensive changes for the retrofit. Might be better to pull it, sell it and buy a custom engine that better suits your needs. |
Quote:
|
R U absolutely sure it's a 427 stroker? A 351 looks the same from the outside
U know. May have to dig into it some. If Wayne says there's something goofy goin' on...believe it. Mike F |
Quote:
You make a great point but I put my trust in the person that sold me the car and I have all the documentation that supports what I was told. I am confident that the motor combination is what it was advertised to be. Wayne did not inspect the motor and then say hey " this sure doesn't look like what you told me it was".....his opinion was based on the power output and how the car performed on his dyno compared against other 427's and Keith setups. Your point is well taken as I know there are some shady things that take place in the industry but I have no doubts about what I bought. I can say that if you pop the hood or get under the car everything from the outside can be verified against what the build documentation is....dart block, intake, distributor, Brodix heads, custom headers. Aside from some improvements I want to make I absolutely love the car! I can't see how people ever sell these things or don't drive them! |
The power output does sound way off to me. I had my Roush 427R rebuilt in the past 5000 miles and had it dynoed after the rebuild. I will look when I get home and let you know what those numbers were. Pretty sure it was a Mustang dyno. Keith Kraft and Roush numbers should be in the same general ballpark for a 427 stroker provided Keith's is not a solid lifter race engine.
|
I would think that if it's one of KC's engines he can maybe tell you all you need to know about the internals and the build? That would be a good starting point in making a plan. Not sure if KC stamps numbers or has other reference points on his builds to keep track, but it seems worth a phone call.;)
|
Ace23, I am back home and looked at my files. FWIW, my Roush 427R with a dual plane intake dynoed at @420rwhp on a Mustang and @460rwhp on a Dynojet. This is a motor that Roush rates @540 flywheel hp. This is a stout motor with an AED 750cfm carb, well tuned and runs 11:30s in the quarter mile on a good day. Your 360rwhp number looks very low to me for the motor you have.
|
Quote:
Quote:
Quote:
|
So you want a lopey cam, and fuel injection? You need to make sure you are pairing the two items. Most of the aftermarket fuel injection systems are complete crap, and while you might get better mpg's, the reliability is hit or miss, more so with mismatched parts. I was interested in it. Now I'm not.
The C6 Z06 feels (should feel) like a dog compared to any windsor Cobra with a 500+hp engine. They are higher revving engines with not so much low end torque. My 530+hp engine did 482rwhp on a dynocom (loaded) and 478rwhp on a mustang dyno (again, loaded). You have something seriously wrong with your engine, and more specifics need to be known, especially for RPM. Most of these engines max out in the mid-upper 5000's, NOWHERE near 7000. I was getting bored with my car so I just put a 175rwhp nitrous shot on it. Interest in the car is back! Quite simply put, it's AWESOME. Before YOu do that, you really need to find out what is wrong with your engine. |
Quote:
*Timing-advanced it in between the dyno pulls until it was shown to lose power. *Air filter removed on dyno- gained a whopping 4hp *Exhaust setup is 2" headers through 2.5" Firefly stainless side pipes *Brand new QF 750......when you go full throttle it was visually inspected and it opens all the way up *Cranks, idles and runs fine and I would get in it and drive 500 miles tomorrow. As mentioned previously I need to get it on the local dyno jet and see what it makes. If it was right I would expect it to make about 450-460rwhp. If it made 360rwhp on a mustang and that dyno was accurate then I expect it to make about 390hp on the dynojet......so lies the magical 60hp that's missing. This isn't rocket science but the first places you look and the initial bases seem to have been covered. |
I'll take a shot at it......
First off I don't think your cold cranking compression numbers are all that bad, cams with a lot of overlap and duration will not show high cranking numbers..and being they are all close together is another good sign..... A 427 stroker built to making the advertised HP as yours was built to do will have an aggressive cam and will not like to run at low rpms like yours,it will come on in the higher rpm range as yours does......it's the nature of the beast...... Your fuel mileage will depend a lot on how your drive the car,if your easy on the gas pedal you should get better than 9-10 mpg,but if your like most of use and like to get on it and run it up to 4000 to 5000+ rpms shifting,well, 9-10 mpg is all you can expect...... Your low rwhp #'s could also be tied in with your exhaust...I'm not familiar with the type you have,but it has been proven time and time again on here that exhaust/mufflers plays a big role in rwhp, some have reported a proven 100hp loss with certain types of headers/mufflers.... taking off the side pipes/mufflers and running a pull or two without them might tell you a story you will not believe..... one or two rear wheel dyno pulls is not enough to tune a car,don't know how many pulls you made or what was done,but at least a half day on a rear wheel dyno will get you the most out of your engine.... each engine I have had on a dyno (engine dyno) was the better part of a day..the tuner tried different jettings and different timing settings and overall at least 20 to 30 hp was gained by trying different configurations.....on my last engine,a change of 2 degrees in the timing was good for 12 hp....we went up/down the timing range from 26 total degrees to 34 total at 2 degree increments and there was a 24 hp difference from 30 to 34 degrees....something you would not know unless it was on a dyno... There are other things besides jetting and timing to take in consideration,air/fuel ratio,volumetric efficiency and a number of other readings to get the most out of what you have...... Unless you go with a "modern" type engine,you will not have a smooth idling,banshee off idle engine, push rod,carbed, stroker motors just don't do that and make 585hp.... You do have a loss of hp somewhere and I think if you can get it figured out and up to where it should be, you'll be more than satisfied with your engine...... good luck with it and keep us posted...... david |
Quote:
Thanks for your input. When the car was tuned the tuner did exaclty as you described......I would say a good 3-4 hours was spent tweaking the carb and making timing adjustments while on the dyno. I guess I have overlooked the exhaust. I called Firefly and they told me the pipes that were purchased for my car should be 2.5". I guess the only way to tell would be to remove and measure to verify. As you have mentioned there are quite a few stories about the HP gained from removing or swapping exhaust. While I have no reason to doubt the Firefly exhaust is better than the stock exhaust I should still investigate this as a possible issue. Its pretty weird how well the car runs to be down on power. Will keep everyone informed if anything is found that relates to the exhaust. Might need to check the headers and how they mount up to the heads as well. The headers were custom made 2" to fit the Brodix heads back in 2004 |
Even with your compression psi being down to what it is,I don't think that would equal to the loss of hp your seeing,just my opinion......
Sounds like your dyno guy tried jetting and timing and got that part optimized to the engine,so taking that out of the picture,it has to be elsewhere...... Not knowing anything about the headers/sidepipes/mufflers other than the diameter,I'm betting there is a big loss there......I'm running 2.5 inch exhaust and 2.5 inch in/out big mufflers on my little 331 stroker and it is in the 400 to 425 hp range..... Inside those 2.5 inch side pipes are mufflers of some sort ( a lot smaller than 2.5 inches) and I think that is a big "choking" point for a 427 stroker engine......I'm betting taking off the side pipes/mufflers will surprise you....For a 585 hp,427 stroker,I would run nothing smaller than 3.5 side pipes and a free flowing muffler to see optimum power... Can you post of photo of the side pipes??? David |
Quote:
|
All times are GMT -7. The time now is 12:41 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: