|
Hole In Trigo wheel.
I've had a slow leak for a while, and it could have been from day one, but I'm not sure. I'm trying to upload a picture but am having trouble getting it into my gallery for some reason. There is no sign of damage, but there is a crack/hole large enough to stick my pinkie finger nail into it, on the inside of the rim. I lose maybe 5 psi per month at the most.
Wasn't Trigo sold? Who can I contact? Can this be repaired? Brad (added picture) http://www.clubcobra.com/photopost/d...003_Large_.jpg |
The fix for that is to peen the area over with an air hammer. PSE fixed one of my wheels that way.
Frank |
I'd take the tire off the rim, and look for the hole on the inside. Clean it off with pain thinner, and coat it with JB weld, and coat the outside as well.
I had a 8" water main spring a leak in my building. I JB Welded the hole from the outside, and it has been holding up well. |
Now that you added a picture I may have to temper my response. That looks like a cavern but in contrast, my wheel wouldn't hold any air so if you're only losing 5lbs a month the inside is probably not too bad. Maybe you could dismount the tire and send it back to Trigo for repair. They should be able to fix you up.
Frank |
hole in wheel
I have the same problem, what is JB weld?
|
JB Weld is MAGIC!...A two part epoxy material that you mix together and which dries to form a hardened sealer/gluing agent for metal/metal, metal/plastic, metal/fiberglass, anything/anything joints or seals.
It comes in a package with two tubes, one epoxy, one hardener. Squeeze out equal amounts and mix together into a paste. You have a limited amount of time to then apply it as a 'hole filler', or as a 'glue' before it hardens into a sandable whole. It is to epoxy resins what Duct Tape is to plastic adhesive tape!!!!! Available at ALL good auto parts stores! :) Glyn |
I'm guessing the leak is not from that surface ding but from the wheel valve. This is a typical area that small leaks occur. To find a leak over inflate your tire (going up to 60 is not a big deal...when the bead is seated during tire installation the presure is usually over 100 ). Put some dish soap in with water (nothing fancy just a couple of soap squirts in a cup), put the soapy water around the valve (or where you think the leak is) then look for air bubbles.
|
leak
I thought that was it as well. Tooki t to two tire stores, they found nothing; but I replced valves both times as a precaution. I'll try the 100lbs and soapy water program. thanks JBo
|
One of my Trigos developed a leak after 6 years. I got a hold of Lynn Park and he said to send it back. I instead had the tire taken off and I painted the inside with aluminum primer. It still leaks but at an acceptable rate. There was no hole or anything you could see on either side. All you could ever see was the soap bubbles forming above the aluminum. Love those cast aluminum wheels.
Bob |
Your nose is also VERY sensitive to air leaks. If you bump up the pressure and get your nose close to it you may be able to detect the leak without making a mess.
Then again, if the neighbors might be watching, the soap may be more prudent :) (See Ethel, I told you he was nuts !). |
The crack/hole bubbled the cleaner I used to prep it for the JB Weld. It's not leaking from the valve. I let all the air out and applied it over the hole, then mounted the tire/wheel back on. I'll fill it with air tomorrow and take it for a ride. :D
|
I would have the wheel checked to make sure there is not a casting flaw of some sort (XRay). Then take it to a company that can properly repair aluminum rims (check yellow pages or ask tire stores recc'd). There are always ads in the back of the enthusiast magazines like Autoweek, Motor Trend, etc for this service. I had an off course excursion about 3 years ago and took a chunk the size of 2 fingers out of the rim and had it repaired with no visible damage for less than $150. I just do not trust JB Weld to hold a wheel together in a car I would be riding in.
|
I agree with 427sharpe, Cracks never get smaller with time. I would hate to see what would happen if that rim let go when you were getting on it and loaded that rim (like when you go thru a turn).
I wonder if the company would replace it free of charge. It is kinda hard to crack a rim in that area, which would lead me to believe it is a defect. Don't get me wrong JB weld has its place but not on my rim at 120mph. :) |
Trigo, which was recently sold, does not replace the wheels. I looked into that. The other problem with getting a new wheel is that they are now painted a different color that they were a little while ago. Like I said before, the air goes right through the aluminum. A little porous I guess.
Bob |
I have to agree with some of the others. I would be careful about an obvious small flaw that may work it's way into a bigger flaw possibly at a very bad moment. Trigo is still around. http://trigowheels.com Contact them and see what they say.
|
rim repair
Take it to a sheet metal shop that does aluminum welding. They should be able to repair your rim. It's an easy repair.
Mechanical fabrication shop also work with aluminum. Dwight |
Check with your local BMW dealer on where they send their wheels for repair. That crack needs to be welded, and then refinished. I've seen both cast and forged wheels that you would swear were ready for the scrap heap be repaired as good as new. The reason I say use a BMW repair shop, is that they will only use a welding shop that is certified in wheel repair, at least that's the local policy. John
|
| All times are GMT -7. The time now is 07:22 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: