cobrajeff
Wed December 23, 2009 6:45am
|
PSE 5.0" wide FIA style "spare" rim
I mounted a 15" Goodyear collapsible spare onto a 5.0" wide rim that Phil Schmidt made for me. Then I painted a blue stripe on it, and highlighted the GoodYear lettering
|
|
jcraigau
Mon December 28, 2009 8:39pm
|
Jag 4 pot front brake pistons
That should buff right out...
|
|
Z-linkCobra
Thu December 31, 2009 5:43am
|
Valley area of the block
Just a pic to show the valley area and reinforcements that are casted into this block.
|
|
52chevyred
Fri January 1, 2010 7:50am
|
Street Beasts Driver Sidepipe
Here is the Street Beasts sidepipe on the driver side. Another lesson learned: if you use a 351W for mock up and are installing a 302, THERE IS A DIFFERENCE! The 302 is 2" narrower (at the head) and about 1" lower (at the head) than the 351. We had to "adjust" the motor mounts when I put the dummy 302 in.
|
|
Wazza
Mon January 25, 2010 6:01pm
|
New Cobra build
The Thunderbird IRS means that the 3 inch system can't be tucked away as much as I wanted...might leave it on show like this.
|
|
FUNFER2
Sat February 6, 2010 5:18am
Rating: 10
|
Hanger
This hanger has a weld tab that is shaped to fit the muffler housing and with the supplied bolts, is adjustable.
|
|
FUNFER2
Sat February 6, 2010 5:46am
Rating: 10
|
Polished 304 stainless steel "Gilmore Kit". Finished.
Finished polished stainless steel side pipe. Cleaning is very easy with a quality polish. Much better than mild steel with a ceramic coating. These may last the life of the car. No glass pack to blow out. I use louvers instead. Look at the "muffler" photo.
|
|
T.L.
Sun February 7, 2010 5:58pm
|
Axles - beefed up ones at that!
|
|
Z-linkCobra
Thu February 18, 2010 8:25am
Rating: 1
|
Hood hinge support
Same thing on the hood. I am going to glass in the aluminum frame so that its solid with hood.
|
|
Beejay
Mon April 26, 2010 4:29am
Rating: 10
|
Cobra Rebuild
Where did that clutch bolt go?
|
|
Badvnm
Mon April 26, 2010 12:44pm
|
My Dream Car
The very beautiful Model (Taylor) had come over to pose for me.. Thank you
|
|
Z-linkCobra
Mon April 26, 2010 2:36pm
|
Radiator mounted too!!
Got that done this weekend too. Well it was done but after I got the hood done and had a good freind come over and take a look...I decided to move it a little...Thanks for the input Russ.
|
|
Wbulk
Wed May 5, 2010 11:15am
Rating: 10
|
Modifed Suspension on a B and B with Modified Upper Mount and Longer Shock
One option for some cars starting around vin 411 that may have had a design problem. The lower A Arm mount was moved up and new higher shock mount was made. This corrected bump steer and roll center flaws. It also gave the suspension a greater travel. Instructions available upon request.
|
|
Wbulk
Fri May 7, 2010 11:44am
Rating: 10
|
Ball Joint Seal Ring
This is a Fix for A Arms that use the Chrystler ball joint without a seal groove machined in. This one was from B and B. A 3/16" steel ring was added to accept the ball joint seal. It was tack tig welded on the outside edges. The rings were cut on a water jet by Kirkhams Motorsports. Barry McGill can also do the fix.
|
|
Wbulk
Sun May 9, 2010 9:03am
Rating: 10
|
Ball Joint Seal Ring
A fix for A Arms shipped without the ball joint seal groove machined in. Ring added to accept a Chrystler Ball Joint Seal. The 3/16" thick rings were cut on Kirkhams Motorsports water jet. Barry McGill can also do the fix. The bad thing was B&B sent me the wrong arms that I paid to get fixed.
|
|
