Robert Sobers
Wed November 9, 2005 10:31am
|
Shelby R Model Clone
My 66 Shelby R Clone Specs.
D.S.S. Pro Bullet 306/308 Short Block Level 10 CNC
Rods: Forgings, shot-peened, Magna Fluxed, CNC Diamond resized and fitted with ARP Wave Loc rod bolts. Balanced to racing tolerances.
Crank: Production crankshaft, thermal cleaned, shot-peened, Magna Fluxed, precision ground, oil scooped and chamfered and balanced to racing tolerances.
Pistons: DSS PRO-LITE Forged 2 valve relief flat top, CNC fly-cut for most aftermarket race cams and heads. Balanced to racing tolerances.
Rings: Sealed Power/ Speed-Pro Moly rings.
Bearings: Tri-metal rod and main bearings.
Block: 5.0 roller cam block, thermal cleaned, stress relieved, Magna Fluxed, threads chased, mains checked and corrected, oil galleys tapped for thread in plugs and the decks are CBN squared and equalized.
Transmission- C4 Automatic
Rear End- 8 Inch Detroit Locker 355 Gears.
Gt40Y Heads ported and polished.
Comp Cam by Bennett Racing Cams.
Edelbrock Air Gap Manifold
670 Holley Street Avenger Carb.
1.6 Roller Rockers
MSD Distributor
MDS 6AL Ignition Control Unit
Edelbrock Fuel Pump
Edelbrock Water Pump
AFCO Aluminum Radiator
Canton 7 QT. Oil Pan
Windage Tray
Shelby R Valve Covers with Vent Stacks
Holley Electric Fuel Pump
3/8 Stainless Fuel Line Tank to Pump
Spal Electric Fan
3 ¾ Auto-Meter Tach
Raptor LED Shift Light
Hurst Quarter Shifter with Line-Lock
K&N X-Stream Air Cleaner
Trunk Mounted Battery with Cut Off Switch
PA Performance 3-G Alt.
PA Performance Mini-Starter
Total Control Products Strut Tower Brace System
Total Control Products Sub-Frame Connectors
Auto-Power Roll Bar
Simpson Safety Harness
Hunsaker Racing Seats
Mac Headers
Mac Exhaust System with 2 ½ Inch Dumps.
R-Model Gauge Panel with 2 5/8 Autometer Gauges.
Cobra Country Oil Breather System.
|
|
Buzz
Mon November 14, 2005 5:31pm
Rating: 9.8
|
alloy w/soft top
polished alloy coachwork and soft top
|
|
lineslinger
Wed December 7, 2005 7:55am
Rating: 10
|
port_job
Ported and Polished
|
|
Tim Rodeheffer
Wed January 4, 2006 6:55pm
Rating: 8.2
|
Bidgog Mastiff Motorcycle
2003 custom Bigdog motorcycle, all chrome , custom paint and polished aluminum.
|
|
Venomus
Fri January 20, 2006 4:19pm
|
Finally....a rolling chassis.
Also a picture of a Stainless fuel tank that we just made. It actually will bolt on from underneath the frame and will be removeable once the body is on. It still need to be polished.
|
|
Dirtrich
Tue February 21, 2006 7:43pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker 505hp build sheet...
• Blue printed machined 351W version Early Casting Block ('69) with Block Girdle Installed
• Scat Forged Steel 4.100 Stroke Crankshaft
• H Beam Rods 6.200" - ARP HD Rod Bolts
• Power Forged 10.5 to 1 Flat Top HP Pistons
• J & E Chrome Moly Ring Set
• Heavy Duty Double Roller Dynagear Timing Set
• Comp Cams Hydraulic Roller Retrofit Camshaft
• Clevite H series Racing Bearings
• Polished Edelbrock Victor Jr. cylinder heads
• Chrome Moly Hardened pushrods
• High Intensity Scorpion True Roller Rockers
• Melling HV Oil pump with Hardened FMS Drive Rod.
• Complete Fel-pro Gasket set
• Heavy Duty Harmonic Balancer
• New SFI Approved 10.5 inch Standard Flywheel
• Aluminum Timing cover
• Aluminum Finned Ford Racing Valve Covers
• New Fuel Lines and Gas Filter
• Polished Edelbrock Vic Jr. Single Plane
• Edelbrock 800 cfm 4 barrel w/ electric choke
• Elec Accel Billet Distributor & high voltage Coil
• High Flow Polished Aluminum Water & Fuel Pump
• Champion Spark plugs w/ 8mm ACCEL Spiral Wires
• New Chrome Thermostat Housing
• Oval aluminum finned air cleaner w/ Cobra logo
• Chrome 100 amp. Alternator and Polished Brackets
• March Pulley Setup with Serpentine-Belt
|
|
Dirtrich
Tue February 21, 2006 8:00pm
Rating: 10
|
SPF 1660 "roadster"
351/418 Stroker - dynoed @ 505hp
I like shiny...so I went with full engine polish as well as Jet Hot ceramic coating of the headers, valve covers, manifold, air filter lid and even the scattershield (which is a no no for you racers).
Why stop there...right? So I also used Stainless steel bolt kit and braided fuel lines.
Note the nickel plated AN fittings and billet fuel filter
|
|
Eljaro
Sun March 19, 2006 9:55am
Rating: 10
|
Weber 48 IDA on 427 C/O
polished carb bodies, all polished stainless steel fasteners, gold spun aluminum stacks.
|
|
Secret Squirrel
Tue April 18, 2006 7:36am
Rating: 10
|
|
HSSS427
Wed April 19, 2006 10:05am
|
ERA #414 427 side oiler after Keith Craft rebuild
427 side-oiler - C5AE-H
Shelby American aluminum heads, stage II port and polish
Forged crank C5AE-6300
Lemans Rods
Aluminum Police Interceptor intake - C6AE-9425-E
Mighty Demon 750 carb
Diamond Pistons
MSD 6AL electronic ignition and billett distributor w MSD 8.5mm wires
Comp Cams hydraulic roller camshaft: 242 duration, .645 lift, 248 duration, .635 lift
Crane lifters, Smith Bros push rods
|
|
hotrods27
Sat April 29, 2006 10:32am
|
c2
All 4 wheels are 16x8 Center line polished aluminum with BFG radial T/A 265/50R16.
|
|
blueovalfanatic
Sun May 7, 2006 4:00pm
|
|
Sydney
Fri June 2, 2006 12:21am
Rating: 5.5
|
|
ferociousfish
Thu July 6, 2006 6:58pm
Rating: 10
|
|
cobra522
Sat September 2, 2006 2:12pm
Rating: 1
|
pwr. steering resv., March polished alternator/pulleys
|
|
